Gasmate Horizon BQ8401 Instruction Manual Download Page 5

5

4

CARE & mAInTEnAnCE

As with all appliances, proper care and 
maintenance will keep them in top operating 
condition and prolong their life. Your new gas 
barbecue is no exception. By following these 
cleaning procedures on a timely basis, your 
barbecue will be kept clean and working properly 
with minimum effort.

Flash-Back 

Spiders and small insects occasionally spin 
webs or make nests in the burner tubes during 
warehousing and transit. These webs can lead to 
a gas flow obstruction which could result in a fire 
in and around the burner tubes.  Cleaning with 
a soft brush before use and at least every six 
months is recommended.
This type of fire is known as ‘FLASH-BACK’ and 
can cause serious damage to your barbecue 
and create an unsafe operating condition for the 
user. Although an obstructed burner tube is not 
the only cause of ‘FLASH-BACK’ it is the most 
common cause and frequent inspection and 
cleaning of the burner tubes is necessary.
If fire occurs in and around the burner, 
immediately turn off gas at its source and 
turn the burner control to ‘OFF’, wait until the 
barbecue has cooled, then clean the burner tubes 
and burner ports.

Cleaning the Cooking Surface

After cooking, turn burner control to ‘OFF’ and 
let barbecue cool before attempting to clean the 
cooking surface. Before first use and periodically, 
it is suggested that you wash the cooking surface 
in a mild soap and warm water solution.

Care of Cooking Surface

Use and care of the cooking surface is important. 
Do not use pans on the cooking surface. Do not 
overheat the cooking surface with the hood down 
or no food on the cooking surface.

Cleaning the drip Tray

To avoid fat or grease dripping from the barbecue 
remove and empty the drip tray after each use. 
Wait until the drip tray is cool to touch before 
disposing of contents.
The drip tray should be washed periodically in a 
mild detergent and warm water solution.   

•  Beware of spiders and wasps.  Burner  
  tube should be inspected and cleaned  
 periodically.
•  This appliance must only be serviced by  
  an authorised person. 
•  To avoid any flare-ups, it is recommended  
  that the drip tray be checked and emptied  
  regularly. Contents of the drip tray may be  
  very hot during cooking. If emptied    
  during extended cooking extreme caution  
  should be taken and direct contact by  
  hand should be avoided at all times. Allow  
  to cool completely before disposing of the  
 contents.

ImPoRTAnT

Summary of Contents for Horizon BQ8401



















Reviews: