background image

3

2

To reduce the risk of personal injury or damage 

to property, follow basic safety precautions when 

using this product, including the following:

READ THESE INSTRUCTIONS 
CAREFULLY BEFORE USING THE 
PRODUCT.  KEEP THE INSTRUCTIONS 
HANDY FOR FUTURE REFERENCE.

Important: Always operate the Product from a 
power source of the same Voltage, Frequency 
and Rating as indicated on the Product 
Identification Plate.
• Close supervision is necessary when any  

Electrical Product is used or operated near  
children or infirm persons; DO NOT leave the  
Product unattended when in use; young  
children should be supervised to ensure that  
they DO NOT play with the Product.

• DO NOT operate any product which has been/ 

or appears damaged in any manner or after  
the Product malfunctions, or is dropped.

•  If it is necessary to use an Extension Cord 

with this Product, prior to its use, make sure 
the extension Cord is safe to use, capable of 
handling the electrical load of the Product (refer 
to Product Identification Plate) and has been 
checked and tested by your electricity supplier 
or qualified technician.

• DO NOT use this heater with a programmer,  

timer or other device that switches the heater  
on automatically, since a fire risk exists if the  
heater is covered or positioned incorrectly.

• Always arrange the Cord so that it cannot be  

pulled or tripped over.

• DO NOT operate this Product immediately  

below an electrical Socket Outlet.

• Always ensure a clearance of 1.5m to any wall  

or combustible surface.

• Avoid operating the Product on long pile carpet 

or uneven surfaces.  Use only on flat,  level and 
stable surfaces. 

•  DO NOT disconnect the Product from the Power 

Supply by pulling on the Cord.  Never move, 
carry or hang the Product by the Cord.

• DO NOT operate this Product in the presence  

of explosive and/or flammable liquid or fumes 
such as where aerosol (spray) Products 
are being used or where Oxygen is being  
administered.

• Avoid leaving the heater unattended when in 

use.

• Switch OFF and UNPLUG from Power Outlet  

when not in use, allow to cool before shifting  
the Product from one location to another, and  
before cleaning.

•  When storing the Product, gently wind the Cord 

around the Cord Wrap if provided, otherwise 
loosely coil the cord.  Avoid wrapping the Cord 
around the Product.

•  DO NOT operate or place any part of this 

Product on or near any hot surfaces such as a 
gas flame, electric element, or near a heated 
oven, or let the Cord hang over the edge of a 
table or bench.

• Avoid touching hot surfaces, use Handles or 

Knobs.

• Avoid contacting moving parts. Keep hands,  

hair, and clothing, well away from the Product  
while it is in operation.

•  DO NOT use the Product for other than its 

intended use as described in these instructions.  
This Product is intended for Normal Domestic 
Household Use only. 

IMPORTANT SAFEGUARDS

Summary of Contents for EH240









Reviews: