background image

IOM GMI 2M & 2ML Nov 2010.doc 

 

 

 

4

 

GMI 2M SPECIFICATIONS AND DIMENSIONS 

 

CGA/AGA Input  
 
CGA/AGA Output  
 
 
 
 
 
Boiler Efficiency @ full load 
 
Water Heater Efficiency @ full load 

Btu/h 
 
Btu/hr 
 
 
Btu/hr 
 
 

 

2,000,000  
 
1,900,000  (as hot water boiler, tested in 
accordance with ANSI Z21.13) 
 
1,960,000 (as water heater, tested in 
accordance with ANSI Z21.10.3 
 
95.0   
 
98.8 

Fuel  

Natural 

Gas 

Electrical Rating 

V/PH/Hz/

120/1/60,208-230/460/575/3/ 60,less than 12 
amps 

Heating surface 

ft

2

 252.0 

Boiler Shell Dimensions 
 

-

 

Width  

-

 

Depth  

-

 

Height  

 
Overall Dimensions 
 

-

 

Width  

-

 

Depth 

-

 

Height  

 
 
Inches  
Inches  
Inches  
 
 
 
Inches  
Inches  
Inches  

 
 
68.125 ±¼ 
25 ±¼ 
64.5 ±¼ 
 
 
 
68.125 ±¼ 
55.5 ±¼ 
85.875 ±¼ 

Shipping Weight

1

 

lbs  

1900  

Supply/Return 
Connections 
 
Water Content 

Inches 
 
 
USG 

3 - Stainless  Steel Flange, ANSI 150 lbs 
 
 
41.0 

Gas connection  

Inches 

2  NPTF 

Gas inlet pressure 

Inches WC  8 to 14 

Flue connection 

Inches 

10 O.D. 

Flue duct material 

 

Stainless Steel (air tight, corrosion resistant) 

Air supply connection  

Inches 

N/A 

Maximum working pressure 

psig 

160 

Maximum working temperature  

Degrees F 

210 

Minimum inlet water temperature  

 

Any temperature above (32

º

F

)

 

Recommended water flow rate

2

 

USG/min 

38 ( For 

T= 100F) 

Minimum service clearance 

Inches 

Top 24, Front 25

3

, Back 24, Floor 0 

Minimum clearances to combustibles 

Inches 

Top 40, Front 40, Back 24, Left Side 24, 
Right Side 24, Floor non-combustible 

1. Dry weight of unit 
2. Above flow rate is for typical boiler condition. For each case, please consult engineering. 
3. Clearance from front of the burner. 

 
 
 

Summary of Contents for GMI 2M




































Reviews: