GASLAND CH775BF Installation Instructions Manual Download Page 27

1. If the cable is damaged or needs replacing, this should be done by an 

    after-sales technician using the proper tools to avoid any accidents.

2. If the appliance is directly connected to the main supply, an omnipolar circuit 

    breaker must be installed with a minimum gap of 0.11

″ 

between the contacts.

3. The installer must ensure that the correct electrical connection has been made 

    and that it complies with safety regulations.

4. The cable must not be bent or compressed.

5. The cable must be checked regularly and only replaced by a properly qualified 

    person.

DISPOSAL: Do not

dispose this product

as unsorted municipal

waste. Collecting such 

waste separately for 

special treatment is

necessary.

This appliance is labeled in compliance with 

European directive 2002/96/EC for Waste Electrical 

and Electronic Equipment(WEEE). By ensuring that 

this appliance is disposed of correctly, you will help 

prevent any possible damage to the environment 

and to human health, which might otherwise be 

caused if it were disposed of in the

wrong way.

The symbol on the product indicates that it may not 

be treated as normal household waste. It should be 

taken to a collection point for the recycling of 

electrical and electronic goods.

This appliance requires specialist waste disposal. 

For more detailed information about treatment, 

recovery and recycling of this product, please 

contact your local city office, your household waste 

disposal service or the shop where you purchased 

the product.

26 

www.gaslandchef.com

8350 Patriot Blvd STE B, N. Charleston, SC 29418

[email protected]

1 (844) 538-7890

Summary of Contents for CH775BF





























Reviews: