Gasboy 2600A Installation Instructions Manual Download Page 9

MDE-4863 Gasboy® 9800A or 2600A Pump Interface Kits Installation Instructions · October 2009

Page 9

Pulse-out I/F Board (M06587A001) Jumper Settings

12

Attach the Bezel. Ensure that the Bezel is seated properly to ensure a watertight seal.

13

Attach and lock the front panel.

14

Turn on the Circuit Breakers.

Pulse-out I/F Board (M06587A001) Jumper Settings

Jumpers JP1, JP2, and JP3

This Board Assembly can be configured for use in one of the following pump/dispenser 
configurations:

• Single-channel, Dual/Single-hose Pulse-out I/F (see 

Figure 7

 on 

page 10

)

• Dual-channel, Single-hose Pulse-out I/F (see 

Figure 8

 on 

page 11

)

The chart below shows the jumper settings and wires to connect to in the Junction Box, based 
on the configuration.

Check JP1 - JP3 jumpers and change them, if necessary. The jumper settings must be changed 
only when the power to the pump/dispenser is removed, to protect the circuit that they are 
connected to.

For models 9800A, 2600A, or 9800Q, the P3 connector is not connected.

Jumper Settings

Single-channel, 

 

Dual/Single-hose Pulse-out I/F

 

(Default Setting)

Dual-channel, 

 

Single-hose Pulse-out I/F 

 

(C07357 kits)

Wire Color

JP1 Position 1
JP2 Position 1
JP3 Open

JP1 Position 2
JP2 Position 2
JP3 Open

Red

Pulse-out Side 1

Pulse-out Side1A

Green

Pulse-out Side 2

Pulse-out Side1B

White

Common Return

Side 1A Return

Black

No Connection

Side 1B Return

Summary of Contents for 2600A













Reviews: