background image

Magnum 6K32F/FR/FC/FRC Managed Switch Installation and User Guide (05/08) 

 

www   GarrettCom   com

.

.

2.0 Introduction 
2.1 

Inspecting the Package and Product 

 

Examine the shipping container for obvious damage prior to installing this 

product; notify the carrier of any damage that you believe occurred during shipment or 

delivery.  Inspect the contents of this package for any signs of damage and ensure that 

the items listed below are included. 

 

This package should contain: 

1

 

Magnum 6K32F, 6K32FR, 6K32FC or 6K32FRC  Managed Switch, base 

unit (configured with user-selected port module option in modular slot) 

AC Power Cord (U.S. and other 115 VAC only) 

Set of metal “Ears” for 19” rack mounting  

Installation and User Guide (this manual) 

  

 

Remove the items from the shipping container.  Be sure to keep the shipping 

container should you need to re-ship the unit at a later date. 

In the event there are items missing or damaged, contact the party from whom 

you purchased the product.  If the unit needs to be returned, please use the original 

shipping container if possible.  Refer to Section 6, Troubleshooting, for specific return 

procedures. 

 

 

 

 

 
 
 
 
 
 
 

 
 
 
 

 

 

Summary of Contents for Magnum 6K32F












































































Reviews: