background image

 
GARNET                                        GAE-3020 

20 

2   Transmit data 
3   Receive data 
4   Data terminal ready 
5   Ground (0v) 

7   Request to send 
8   Clear to send 
9   Not connected 

 
3.1.2 J2 – ADSL Port 
RJ11 connector to connect to DSLAM or to PSTN 
PinDescription 
Pin   Description 
 

Pin    Description 

1     Tr 
2     Transmit - 

3         

Not connected

 

4     Receive - 

 
3.1.3 J3 - Ethernet Port 
RJ45 type 10BaseT Ethernet connector. This connector is wired as an Ethernet 
NIC. 
Pin   Description 

Pin   Description 

1     Tr 
2     Transmit – 
3     R 
4         

Not connected

 

5         

Not connected

 

6     Receive –  
7         

Not connected

 

8         

Not connected

 

3.2 WARRANTY

 

 

LIMITED WARRANTY 

 

Garnet Systems warrants that the product will be free from defects in materials or workmanship for a 

period of        years from the date of purchase. Under this limited warranty, and upon proof of purchase, our 

obligation is limited to repairing or replacing any product or parts proved to be defective at the inspection. 

The product will be repaired or replaced (with the same or a similar model) at our option, without charge for 

either parts or labor. This limited warranty shall not apply if the product is modified, tampered with, misused, 

or subjected to abnormal working conditions (Including, but not limited to, lightning and water damage). 

 

THIS LIMITED WARRANTY DOES NOT GUARANTEE YOU UNINTERRUPTED SERVICE. THE 

FOREGOING REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY OF THE 

PURCHASER, AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, OR 

STATUTORY AS TO MERCHANTABILITY, FITNESS FOR PURPOSE SOLD, DESCRIPTION, QUALITY, 

PRODUCTIVENESS OR ANY OTHER MATTER. WITHOUT LIMITING THE FOREGOING REPAIR OR 

REPLACEMENT, IN NO EVENT SHALL GARNET SYSTEMS BE LIABLE FOR THE LOSS OF USE OR 

PROFIT OR OTHER COLLATERAL, SPECIAL OR CONSEQUENTIAL DAMAGES. 

Summary of Contents for GAE-3020























Reviews: