manualshive.com logo in svg

Garmin GTX 325, Installation Manual, Page: 52 / 67

Share
Download
Garmin GTX 325 Installation Manual Download Page 52

190-01499-02

GTX 3x5 TSO Installation Manual

Rev. 1

Page 6-3

6.4.5 RS-422

6.4.6 HSDB

6.4.7 Pressure Sensor Correspondence

The optional pressure sensor module requires a correspondence adjustment to match the aircraft primary 
altitude display. 

6.5 Remote Unit Configuration

6.6 Diagnostic Information

6.7 Ground Checks

6.7.1 Interface Checkout

6.7.2 GPS Reception

The GPS checks described in this section are applicable to GTX 335 and GTX 345 units with the internal 
GPS receiver.

6.7.2.1 VHF COM Interference Check

1. Using the GPS status page, verify.
2. Select 121.150MHz on the com transceiver to be tested.
3. Transmit for a period of 35 seconds.
4. Verify.
5. Repeat steps 3 and 4 for the following frequencies.

121.15MHz

131.22MHz

121.17MHz

131.25MHz

121.20MHz

131.27MHz

121.22MHz

131.30MHz

121.25MHz

131.32MHz

131.20MHz

131.35MHz

6. For VHF radios that include 8.33 kHz channel spacing, include the following frequencies in 

addition to those listed above.

Selection

Description

Summary of Contents for GTX 325




































































Reviews:

No comments