background image

USB repeater extension cable only. You should make all cable 

connections in a dry environment.

Item

Description

Garmin chartplotter

Computer

GPSMAP USB cable

Dry environment, protected from moisture

GPSMAP HDMI cable (HDMI IN)

Controlling a Computer with the Chartplotter

Before you can control a computer using the chartplotter, you 

must connect the chartplotter and computer correctly. See the 

chartplotter installation instructions for connection information.

1

Select 

OneHelm™, A/V, Gauges

 > 

Video

.

2

Select the HDMI source for the computer.

3

Select 

Menu

 > 

USB Touch Out

.

You can now control your computer using two-finger touch 

gestures on the chartplotter screen.

4

If necessary, select 

Menu

 > 

Full Screen

 to view the 

computer screen in full screen mode.

TIP: 

To exit full screen mode, press  .

Pairing the GRID Device with the 

Chartplotter from the Chartplotter

NOTE: 

These steps are applicable to both the GRID device and 

the GRID 20 device.
Before you can pair the GRID 20 device with the chartplotter to 

make the data connection, you must supply power using 

batteries, the included power cable, or a NMEA 2000 network 

connection.
Before you can pair the GRID device with the chartplotter, you 

must connect it to the Garmin Marine Network.

1

Select 

Settings

 > 

System

 > 

Station Information

 > 

GRID™ 

Pairing

 > 

Add

.

2

Select an action:
• On the GRID remote input device, press 

SELECT

.

• On the GRID 20 remote input device, press   and   until 

the remote control beeps three times.

Pairing the GRID Device with the Chartplotter from 

the GRID Device

NOTE: 

This is not applicable to the GRID 20 device.

1

On the GRID remote input device, press 

+

 and 

HOME

 at the 

same time.
A selection page opens on all of the chartplotters on the 

Garmin Marine Network.

2

Rotate the wheel on the GRID remote input device to 

highlight 

Select

 on the chartplotter you want to control with 

the GRID remote input device.

3

Press 

SELECT

.

Rotating the GRID Remote Input Device

For certain installation situations, you can rotate the orientation 

of the GRID device.

NOTE: 

This is not applicable to the GRID 20 device.

1

Select 

Settings

 > 

Communications

 > 

Marine Network

.

2

Select the GRID device.

Cleaning the Screen

NOTICE

Cleaners containing ammonia will harm the anti-reflective 

coating.

The device is coated with a special anti-reflective coating which 

is very sensitive to waxes and abrasive cleaners.

1

Apply an eyeglass lens cleaner specified as safe for anti-

reflective coatings to the cloth.

2

Gently wipe the screen with a soft, clean, lint-free cloth.

Viewing Images on a Memory card

You can view images that are saved on a memory card. You 

can view .jpg, .png, and .bmp files.

1

Insert a memory card with image files into the card slot.

2

Select 

Info

 > 

Image Viewer

.

3

Select the folder containing the images.

4

Wait a few seconds for the thumbnail images to load.

5

Select an image.

6

Use the arrows to scroll through the images.

7

If necessary, select 

Menu

 > 

Start Slideshow

.

Screenshots

You can capture a screenshot of any screen shown on your 

chartplotter as a .png file. You can transfer the screenshot to 

your computer. You can also view the screenshot in the image 

viewer (

Viewing Images on a Memory card

, page 60

).

Capturing Screenshots

1

Insert a memory card into the card slot.

2

Select 

Settings

 > 

Preferences

 > 

Screenshot Capture

 > 

On

.

3

Go to a screen you want to capture.

4

Hold 

Home

 for at least six seconds.

Copying Screenshots to a Computer

1

Remove the memory card from the chartplotter, and insert it 

into a card reader that is attached to a computer.

2

From Windows Explorer, open the Garmin\scrn folder on the 

memory card.

3

Copy a .bmp file from the card and paste it to any location on 

the computer.

Troubleshooting

My device will not acquire GPS signals

If the device is not acquiring satellite signals, there could be a 

few causes. If the device has moved a large distance since the 

last time it has acquired satellites or has been turned off for 

longer than a few weeks or months, the device may not be able 

to acquire the satellites correctly.
• Ensure the device is using the latest software. If not, update 

the device software.

• If the device is using an internal GPS antenna, make sure the 

device has a clear view of the sky so the internal antenna can 

receive the GPS signal. If it is mounted inside of a cabin, it 

should be close to a window so it can receive the GPS signal. 

60

Appendix

Summary of Contents for GPSMAP 8600 series





































































Reviews: