Av. Kit Install. Manual
190-00067-62 Rev. E
Page 12
011-00154-00
MOUNTING RACK, (WITHOUT CONNECTORS)
Note: A mounting rack is required for approved installations. The following hardware is required
for installation of the mounting rack, but is not provided:
#6-32 Flat Head Screw (4 ea.) #6-32 Self-locking Nut (4 ea.)
011-00313-00 CONNECTOR, (J1 and J2) Kit (GNC 250/GNC 250XL)
011-00313-01
CONNECTOR,(J1) Kit (GPS 150XL)
DATA BASE OPTIONS
010-10038-00
MEMORY CARD - WORLDWIDE DATABASE
010-10038-01
MEMORY CARD - AMERICAS DATABASE
010-10038-02
MEMORY CARD - INTERNATIONAL DATABASE
010-10032-03
MEMORY CARD - USER
MISCELLANEOUS OPTIONS
010-10075-00
PC KIT
190-00067-50
GNC 250 PILOT'S GUIDE
190-00067-51
GNC 250 QUICK REFERENCE GUIDE
190-00067-56
GNC 250 IN MOONEY M20J DOCUMENTED INSTALLATION
190-00067-60
GNC 250XL PILOT'S GUIDE
190-00067-61
GNC 250XL QUICK REFERENCE GUIDE
190-00067-66
GNC 250XL IN MOONEY M20J DOCUMENTED INSTALLATION
190-00067-80
GPS 150XL PILOT'S GUIDE
190-00067-81
GPS 150XL QUICK REFERENCE GUIDE
190-00067-86
GPS 150XL IN MOONEY M20J DOCUMENTED INSTALLATION
330-00067-00
GPS 1.57542 GHZ NOTCH FILTER
362-00014-00
WALL ADAPTER - 110 VAC
010-10057-00
28 TO 14V CONVERTER (GNC 250/GNC 250XL ONLY) (Consists of 011-00181-00)
010-10074-00
REMOTE BATTERY PACK (Consists of 011-00182-00)
THE FOLLOWING INSTALLATION ACCESSORIES ARE REQUIRED BUT NOT PROVIDED: (GNC 250/GNC 250XL ONLY)
COMM ANTENNA:
BROAD BAND 50 OHM VERTICALLY POLARIZED WITH COAXIAL CABLE.
HEADPHONES:
500 OHM NOMINAL IMPEDANCE
MICROPHONE
LOW IMPEDANCE CARBON OR DYNAMIC WITH TRANSISTORIZED PRE-AMP.
3.2
ANTENNA INSTALLATION
For the COMM antenna, follow the manufacturers instructions. (GNC 250/GNC
250XL only)
The remainder of this section applies to the GPS antenna. The GA 56 Antenna outline
and footprint dimensions are shown in Figures 3-1 and 3-2.
A. Using the backing plate as a template, mark the location of the mounting holes
and the through hole for coax cable. Drill or punch the holes.
B. The antenna installation must provide adequate support for the antenna
considering a maximum drag load of 5 lbs. for the GA 56 antennas (at subsonic
speed). Install a doubler plate to reinforce thin skinned aircraft. Observe
guidelines for acceptable installation practices as outlined in AC 43.13-2A.
C. Seal the antenna and gasket to the fuselage using a good quality electrical grade
sealant. Use caution to insure that the antenna connector is not contaminated
with sealant. Insure that the mounting screws are fully tightened and that the
antenna base is well seated against the gasket. CAUTION: Do not use
construction grade RTV sealant or sealants containing acetic acid. These sealants
may damage the electrical connections to the antenna. Use of these type sealants
may void the antenna warranty.
Summary of Contents for GNC 250
