background image

GMR

 430/1230/2530 XHD3 SERIES

 

INSTALLATION INSTRUCTIONS

Important Safety Information

 WARNING

See the Important Safety and Product Information guide in the product box for product warnings and other 
important information.
Failure to install this device according to these instructions could result in personal injury, damage to the vessel 
or device, or poor product performance.
The radar transmits electromagnetic energy. To avoid possible personal injury, damage to the vessel or device, 
or poor product performance, ensure that the radar is installed according to the recommendations in these 
instructions and that all personnel are clear of the path of the radar beam before transmitting. When properly 
installed and operated, the use of this radar conforms to the requirements of ANSI/IEEE C95.1-1992 Standard 
for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields.
To avoid possible personal injury, do not look directly at the antenna at close range when the radar is 
transmitting. Eyes are the most sensitive part of the body to electromagnetic energy.
When connecting the power cable, do not remove the in-line fuse holder. To prevent the possibility of injury or 
product damage caused by fire or overheating, the appropriate fuse must be in place as indicated in the product 
specifications. Connecting the power cable without the appropriate fuse in place voids the product warranty.

 CAUTION

For the best possible performance and to avoid potential injury, damage to the device, or damage to your vessel, 
installation by a qualified marine installer is recommended.
Opening the device may result in personal injury and/or damage to the device. This device contains no user-
serviceable parts, and should be opened only by a Garmin

®

 authorized service technician. Any damage resulting 

from opening the unit by anyone other than a Garmin authorized service technician will not be covered by the 
Garmin warranty.
This device should be used only as a navigational aid. Using the device for any purpose requiring precise 
measurement or direction, distance, location, or topography may result in personal injury or damage to the 
vessel.
To avoid possible personal injury, always wear safety goggles, ear protection, and a dust mask when drilling, 
cutting, or sanding.

NOTICE

When drilling or cutting, always check what is on the opposite side of the surface to avoid damaging the vessel.

Software Update

You must update the Garmin chartplotter software when you install this device. For instructions on updating the 
software, see your chartplotter owner's manual at 

support.garmin.com

.

GUID-EB209D1E-8C29-450E-B406-01E29CD7AD9A v2

June 2023

Summary of Contents for GMR 430 XHD3 Series





















Reviews: