background image

GHP 10V Installation Instructions 

1

GHP

 10V Installation Instructions

To obtain the best possible performance and to avoid damage to your 

boat, install the Garmin

®

 GHP 10V marine autopilot system according 

to the following instructions. Professional installation of the autopilot 

system is highly recommended. 
The GHP 10V is compatible with C3 or newer Volvo

®

 EVC systems. 

Contact Volvo for more information on updating older EVC systems.

Read all installation instructions before proceeding with the 

installation.

 If you experience difficulty during the installation, contact 

Garmin Product Support.

NOTE:

 There is an installation checklist on the last page of these 

instructions. Remove the last page and refer to the checklist as you 

proceed through the GHP 10V installation.

Registering Your Device

Help us better support you by completing our online registration today.
•  Go to 

http://my.garmin.com

•  Keep the original sales receipt, or a photocopy, in a safe place.
For future reference, write the serial number assigned to each 

component of your GHP 10V system in the spaces provided on 

page 3

The serial numbers are located on a sticker on each component.

Contacting Garmin

Contact Garmin Product Support if you have any questions while using 

your GHP 10V.
In the USA, go to 

www.garmin.com/support

, or contact Garmin USA 

by phone at (913) 397.8200 or (800) 800.1020.
In the UK, contact Garmin (Europe) Ltd. by phone at 0808 2380000.
In Europe, go to 

www.garmin.com/support

 and click 

Contact Support

 

for in-country support information, or contact Garmin (Europe) Ltd. by 

phone at +44 (0) 870.8501241.

Important Safety Information

 WaRnInGS

You are responsible for the safe and prudent operation of your 

vessel.

 The GHP 10V is a tool that will enhance your capability to 

operate your boat. It does not relieve you from the responsibility of 

safely operating your boat. Avoid navigational hazards and never leave 

the helm unattended.
Always be prepared to promptly regain manual control of your boat.
Learn to operate the GHP 10V on calm and hazard-free open water.
Use caution when operating the GHP 10V near hazards in the water, 

such as docks, pilings, and other boats.
See the 

Important Safety and Product Information

 guide in the product 

box for product warnings and other important information.

 CautIon

Equipment to be connected to this product should have a fire enclosure 

or be provided with a fire enclosure.
Always wear safety goggles, ear protection, and a dust mask when 

drilling, cutting, or sanding.

Notice

When drilling or cutting, always check the opposite side of the surface. 

Be aware of fuel tanks, electrical cables, and hydraulic hoses.

Summary of Contents for GHP 10V





















Reviews: