![background image](http://html1.mh-extra.com/html/garland/scar-322-e/scar-322-e_instruction-manual_3647214029.webp)
English
English
29/112
6.4. INSTALLATION OF THE WORK CYLINDER
This machines has two working cylinders, one for
scarifying and one for aeration. The scarifying cylinder
comes mounted on the machine.
Always carry out maintenance work or servicing with
the machine unplugged from the mains. Unplug the
machine before carrying out any work on the machine.
Read the instruction manual before carrying out any
maintenance work.
The working cylinders are sharp and heat up during
use. Always use gloves when handling the cylinders to
avoid damages to your hands.
To change the cylinder, follow these steps:
1. Remove the catcher.
2. Turn the machine over on a flat surface so to have
easy access to the under part of the machine.
3. Loosen the screws (1) and remove them the
clamp of the cylinder axis (2).
6.5. HOLDING THE CABLE EXTENSION
Only use cable extensions that are
certified for outdoor use. The cable
section must be at least 2.5mm
2
, the
cable will have a maximum length of
25m and it must be fully unrolled before
starting to work.
Fix the cable extension to the fixing hook provided as
seen in the figure.
6.6. CONNECTING TO THE MAINS
It is mandatory that this machine is connected to
a switch protected by a differential whose current
is 30mA maximum. The tension must be 230V, the
frequency 50Hz and it must have a circuit breaker of
10A-16A.
Never use a damaged cable or a damaged electric
mains, or that does not comply with current normative
or those required for this machine. When using a
electric extension for the cable, make sure that it has
a minimum section of 2.5 mm
2
and it should not be
longer than 25metres in length and homologated for
outdoor use. Both the plug and the base of the electric
extension must be waterproof and should never be
submerged in water. The use of an adequate electric
extension will reduce the risk of electric shock.
6.7. CHECKING POINTS PRIOR TO USING THE
MACHINE
Check all the machine and make sure that there are
no loose parts (screws, nuts, knobs etc) and any
damages to the machine.
Tighten, repair or replace all necessary equipment
prior to using the machine.
Check the state of the catcher and that it is properly
in place. Do not use the machine if it is damaged or
not properly regulated.
1
2
Summary of Contents for SCAR 322 E
