background image

11

6. Mounting Instructions

 CAUTION!

 

THE BATTERY TAMPER BUTTON MUST BE HELD 

DOWN IN THE BATTERY COMPARTMENT BY THE BATTERY, 

TO ENSURE THE BATTERY DOOR WILL CLOSE, THE AC QUICK 

CONNECTOR WILL ATTACH TO THE ALARM, AND THE ALARM 

WILL ATTACH TO THE TRIM RING.
NOTE: PLEASE ENSURE THAT BATTERY IS INSTALLED PRIOR 

TO MOUNTING OF SMOKE ALARM.

A trim ring is provided on the back of the smoke alarm. This trim ring 

is removed by holding the trim ring and twisting the smoke alarm in 

the direction indicated by the turn to remove arrow. The trim ring is 

secured to the smoke alarm by a trim lever.

 

Caution! The cover is a sealed unit and has no removable 

serviceable parts! Do not tamper.

1. Secure a suitable junction box near 

the position of the smoke alarm, 

ensure the quick connect cable 

length is long enough to reach the 

junction box for termination to be 

made.

2. Connect active, neutral and switch 

line to the smoke alarm cable 

using the terminal connection 

block provided. Secure these 

terminals inside the junction box.

3. Punch out the suitable fixing holes 

on the trim ring and then pull the 

AC connector through the centre 

of the trim ring.

4. Secure the trim ring to the ceiling 

using the fixing holes provided.

Connect the 9V battery (back up) 

into the battery compartment. If 

the back up 9V battery is already 

loaded in the Battery compartment, 

pull out the battery pull tab. Ensure 

the locks on the AC connector 

snap firmly into place. 

SQUEEZE

CONNECTOR

LOCKING

ARMS AND PULL

INSTALL

MARKS

REMOVE

FIGURE 4A

FIGURE 4B

Summary of Contents for Ongard OG10























Reviews: