background image

Description 

115051 

11 

3.1.2 

Diaphragm pump 

► Design:

The diaphragm pump consists of a pump body and a drive motor. 
The pump body consists of a drive shaft and four pump heads. Each pump head contains 

the diaphragm and the work valves. The two pump heads are arranged opposite each other. 

In a three-stage (T) diaphragm pump, the two pump heads are connected in parallel, two fur-

ther pumps in series. 
The pump heads are driven via an eccentric shaft with a connecting rod. 

► Function:

Motor, eccentric shaft and connecting rod set the diaphragms in stroke movement. This 

changes the size of the space between the diaphragms and pump head (pump chamber). 
Increasing the size of the pump chamber opens the inlet valve while the outlet valve is 

closed (intake process). Decreasing the size of the pump chamber ejects the gas through 

the outlet valve. 
The valves are actuated by the gas being pumped. A large proportion of fluid in the dia-

phragm pump minimizes the pumping efficiency. 

► Materials of the medium-affecting pump parts:

Component 

Materials 

Seal

EPDM

Screw fitting / Connecting elements

PP, PVDF

Valve

PEEK

Diaphragm

Ela PTFE layer

Vacuum hose

PTFE

Connection head / pump head

PTFE with carbon-fibre reinforcing

 *)

*) 

  electrically conductive (with manufacturer's certificate of electrical conductivity) 

 Material resistance to aggressive media see: Publisher Hoppenstedt Publishing (18. September 2007) 

► Gas ballast:

When condensable vapours are pumped, 

they may be compressed above the 

saturated vapour pressure and condense.

Opening the gas ballast valve (17) in the 

suction line of the last pump stage allows 

air to flow into the pump chamber. 

This prevents condensation and flushes 

the pump clear.

Operation leads to increasing the ultimate pres-

sure and the operating temperature.

        Fig. 2   Diaphragm pump MPC 601 T 

Summary of Contents for WELCH LVS 600 T





































































Reviews: