background image

16

Welch Vacuum by Ingersoll Rand

1601 Feehanville Drive, Ste 550

Mount Prospect, IL  60056

Phone: (847) 676-8800  (Technical Support)

Fax: (847) 677-8606 

E-Mail: [email protected]

Web-Page: www.welchvacuum.com

Copyright© 1997-2007 Gardner Denver Welch Vacuum Technology, Inc.    

Welch is registered trademarks of Gardner Denver

Warranty

 

 

This Welch Vacuum product is warranted to be free from defects in material and  workmanship.  This 

 

liability of Gardner Denver Welch Vacuum Technology under this  warranty is limited to servicing, 

 

adjusting, repairing, or replacing any unit or  component part which in the judgment of Gardner Denver 

 

Welch Vacuum Technology  has not been misused, abused, or altered in any way or damaged by 

 

ingestion of  foreign material causing impaired performance or rendering it inoperative.  No other 

 

warranties are expressed or implied.   The method of executing this warranty: servicing, adjusting, 

 

repairing, or replacing,  shall be at the discretion of Gardner Denver Welch Vacuum Technology.  

 

Vacuum  pumps that have been operated within a vacuum system, or other system, for any  period, 

 

however short, will be repaired under this warranty rather than replaced.    

 

The warranty is eff ective for one year from the date of original purchase when:       

 

 

1. The warranty card has been completed and returned.       

 

 

2. The product is returned to the factory or other designated service centers, freight prepaid.       

 

 

3. The product in our judgment is defective through no action or fault of the user. 

 

If the product has become defective through misuse, abuse, alteration, or ingestion of foreign material, 

 

repairs will be billed regardless of the age of the product.  In this event, an estimate of the repair costs 

 

will be submitted and authorization of these charges will be required before the product is repaired and 

 

returned.

Summary of Contents for Welch 2580B-01

















Reviews: