background image

Welch Vacuum by Ingersoll Rand

1601 Feehanville Drive, Ste 550

Mount Prospect, IL 60056

Phone: (847) 676-8800 (Technical Support)

Fax: (847) 677-8606

E-Mail: [email protected]

Web-Page: www.welchvacuum.com

Copyright© 1997-2007 Gardner Denver Welch Vacuum Technology, Inc.

Welch is registered trademarks of Gardner Denver

Section 8: WARRANTY

 
This Welch Vacuum product is warranted to be free from defects in material and workmanship. This 
liability of Welch-Ilmvac under this warranty is limited to servicing, adjusting, repairing, or replacing 
any unit or component part which in the judgment of Welch-Ilmvac has not been misused, abused, 
or altered in any way or damaged by ingestion of foreign material causing impaired performance 
or rendering it inoperative. No other warranties are expressed or implied. The method of executing 
this warranty: servicing, adjusting, repairing, or replacing, shall be at the discretion of Welch-Ilmvac. 
Vacuum pumps that have been operated within a vacuum system, or other system, for any period, 
however short, will be repaired under this warranty rather than replaced.

The warranty is eff ective for one year from the date of original purchase when:
1. The warranty card has been completed and returned.
2. The product is returned to the factory or other designated service centers, freight prepaid.
3. The product in our judgment is defective through no action or fault of the user. 

If the product has become defective through misuse, abuse, alteration, or ingestion of foreign 
material, repairs will be billed regardless of the age of the product. In this event, an estimate of the 
repair costs will be submitted and authorization of these charges will be required before the product is 
repaired and returned.

Summary of Contents for WELCH 2567B-01

















Reviews: