background image

 

RFL-7-500     Page  4 

2.  SAFETY RULES & NOTES ON DANGER 

2.1 

Intended Usage 

The compressor/vacuum pump is designed exclusively for compression or suction of filtered air. Use for any other purpose 
is not considered intended use. 

Intended use also requires adherence to the operating data and listed maintenance as set forth in this manual. 

2.2 

Acceptance & Monitoring 

The compressor/vacuum pump itself is not subject to any general acceptance and monitoring requirements. 

The operator is responsible for meeting any special regulations that are in effect at the site of operation. 

2.3 

Operational Safety 

 

This symbol indicates possible dangers for personal safety. Working safety requires exact observation of 
instructions so marked. Safety instructions must be known to all personnel who use the machine! 

2.4 

Environmental Protection 

 

This symbol shows that environment protection regulations must be observed. 

2.5 

ATTENTION 

 

“ATTENTION” defines regulations and instructions which are designed to prevent damage to the machine. 

2.6 

Information 

 

This symbol indicates information of particular interest to the operator of the machine! 

2.7 

Points to Note 

 

The compressor/vacuum pump has been constructed according to the latest technological standards and safety 
regulations; however, during use of the machine it is still possible that the health and life of the operator or other 
personnel may be endangered, or that damage to the machine or to other property may be caused. 

 

Only use the machine when it is in a technically perfect condition; such use must be carried out in accordance with the 
intended usage and with due regard for safety. In particular, any faults which are relevant to the safety of the machine 
must be repaired immediately. 

 

Alterations, attachments or modifications to the compressor/vacuum pump which may affect the safety of the machine 
are not acceptable without consulting the manufacturer. 

 

All warning notices on the machine must be observed, and care must be taken that all such notices are always in legal 
condition. 

 

Attention must be paid to fire detection and fire-fighting features. 

 

Work on electrical devices must be carried out by a qualified electrician in accordance with the electrical and technical 
regulations. 

Summary of Contents for RFL Series





































Reviews: