background image

 

13-8-619    Page 34 

 

SECTION 6 
AIR FILTER 

  

 

Figure 6-1 – STANDARD DUTY AIR FILTER 

 

STANDARD DUTY AIR FILTER

 (Figure 6-1) - Service and replacement instructions are given in the 

following sections:  Filter Element and Filter Element Life. 
 

Filter Element 

- The element should be serviced when inspection indicates an accumulation of dirt on the 

outside of the element.  Clean every 100 to 500 operating hours depending on dust conditions.  Inspect 
every few days until experience determines the proper time interval for servicing. 
 
To Service: 
 
1. 

Remove element from filter housing. 

 
2. 

Blow off excess dirt with air nozzle.  Direct air blast parallel to element pleats at a slight upward 
angle.  Do not point air blast directly at element. 

 
3. 

Inspect for rupture by placing a bright light inside the element.  The slightest rupture requires 
replacement of the element. 

 

Filter Element Life

 - The element should be replaced after eight cleanings or if visual inspection 

indicates a rupture, crack or pin hole in the pleated media.  Inspection should be done by placing a bright 
light inside the element. 
 
 

WARNING 

Do not oil this element.  Never operate unit without element.  Never use 
elements that are damaged or ruptured.  Never use elements that won’t seal.  
Keep spare elements on hand to reduce downtime.  Store elements in a 
protected area free from damage, dirt and moisture.  Handle filter parts with 
care. 

 

 

Summary of Contents for INTEGRA EFB99A






















































Reviews: