background image

 

Instruction Manual 

Top & Bottom Loading Arms 

E2110, E2112, E2022, E2025 

E2033, E2304, E2573, E2123, 

E2313, E2121 

 

 

 

- 9 - 

 

Note 

 

All control components have been adjusted to correct 
values during fabrication. Do not change these values 
without written consent from EMCO WHEATON. 

6.2 Installation of Feed Lines 

Only persons with the required training and qualification (i.e. electricians for the 
electrical systems or mechanics for the pneumatic and hydraulic system) are al-
lowed to work on the electrical, pneumatic and hydraulic system. 

Install and connect all pneumatic and hydraulic lines according to appropriate 
industry standards. Fittings, dimensions and quality of the components must be 
selected to meet the requirements of the installation. 

Clean all pipes and containers from dirt (scales, sand, swarf etc.) before installa-
tion. 

Connect the electrical system, the pneumatic system and the hydraulic system (if 
applicable) according to the diagrams and data sheets in the appendix. 

All components have been adjusted to their values during fabrication. Do not 
change these values without our written consent. 

Only use dry and clean air or nitrogen for the pneumatic system. 

7 Commissioning 

Do not operate the loading arm when you notice any damage. Please contact 
EMCO WHEATON. 

Purge the system (loading arm and pipes) before using for the first time to avoid 
damaging the swivel joints and fittings. 

Perform the following tests: 

  Leakage Test 

Leak test by means of air or nitrogen of 7 to 15 psi and a foam-forming 
substance. 

  Operating Range/Balancing 

Check the operating range once again by moving the A/B/F-lengths of the 
loading arm into the extreme positions. Verify with the help of the general 
arrangement drawing. 

  Functional Test:  

Operate the loading arm as described in Section 8. Test the function of all 
instruments, accessories and signals. 

Do not exceed the allowable operating pressure and operating temperature. 

 

 

 

Summary of Contents for EMCO WHEATON E2110






















Reviews: