background image

9

www.gd-elmorietschle.com

 © Gardner Denver Schopfheim GmbH, Gardner Denver Deutschland GmbH

 

|

Safety

2.8  Safety instructions for installing, commissioning and maintenance

 

•  The operator will ensure that any installation, 

commissioning and maintenance work is car-
ried out by authorised, qualified specialists who 
have gained sufficient information by an in-depth 
study of the operating instructions.

 

•  Only work on the machine when it is idle and 

cannot be switched on again

 

•  Ensure that you follow the procedure for decom-

missioning the machine described in the operat-
ing instructions.

 

•  Fit or start up safety and protective devices 

again immediately after finishing work.

 

•  Conversion work or modifications to the ma-

chine are only permissible with the manufactur-
er’s consent.

 

•  Only use original parts or parts approved by the 

manufacturer. The use of other parts may invali-
date liability for any consequences arising.

 

•  Keep unauthorised people away from the ma-

chine

2.9  Guarantee conditions

The manufacturer’s guarantee or warranty will no 
longer apply in the following cases:

 

•  Improper use

 

•  Not complying with these instructions

 

•  Operation by insufficiently qualified staff

 

•  Using spare parts that have not been approved 

by 

Gardner Denver Schopfheim GmbH

 

•  Unauthorised modifications to the machine or 

the accessories supplied by 

Gardner Denver 

Schopfheim GmbH

Summary of Contents for Elmo Rietschle C-VLR 301





























Reviews: