background image

16

|

 

www.gd-elmorietschle.com

 © Gardner Denver Schopfheim GmbH, Gardner Denver Deutschland GmbH

Installation

5.5  Connecting the motor

 

DANGER

 

Danger of death if the electrical installation has 
not been done professionally.

The electrical installation must only be done by a 
qualified electrician observing EN 60204. The
operating company has to provide the main 
switch.

 

a)  The motor‘s electrical data is given on the data 

plate (Fig. 2/N) or on the motor data plate (Fig. 2/
P

1

). The motors comply with DIN EN 60034 

and are in protection class IP 55 and insulation 
class F. The appropriate connection diagram is 
located in the motor‘s terminal box (not for the 
plug connection version). The motor data must 
be compared with the data of the existing mains 
network (current type, voltage, network frequen-
cy, permitted current value).

 

b)  Connect the motor via the plug connection or 

the motor protection switch (for safety reasons, 
a motor protection switch is required and the 
connecting cable must be installed via a cable 
fitting to provide strain relief). 
We recommend using motor protection switches 
with delayed switch off, depending on possible 
excess current. Temporary excess current may 
occur when the machine is started cold.

 

NOTICE

 

Power supply

The conditions at the installation location must match 
the information on the motor data plate.
Without derating the following is permissible:

•  ± 5% Voltage deviation
•  ± 2% Frequency deviation

Summary of Contents for Elmo Rietschle C-VLR 301





























Reviews: