Gardenline 31CC 4 STROKE User Manual Download Page 35

Understanding and using these operating instructions

                

31cc Brushcutter / Line Trimmer

AFTER SALES SUPPORT

e-mail: [email protected]

1800 909 909

MODEL: №. WLBCF310  •  08/2015  •  49290

(toll free)

Operating instructions and safety notes!

AFTER SALES SUPPORT

(toll free)

31cc Brushcutter / Line Trimmer

e-mail: [email protected]

1800 909 909

MODEL: №. WLBCF310  •  08/2015  •  49290

33

NOTE:

 Be aware that when using the 3T brushcutter blade (28), it will take a 

few seconds to run down.

IMPORTANT: 

 If the cutting head (spool and line) does not disengage and stop 

when the throttle is in the idle position, TURN OFF the petrol motor and have 

the unit checked at a service centre.

Stopping the Brushcutter/ Line Trimmer

1.   Release the throttle trigger (8) and allow the engine to idle for a  

few moments.

2.   Move the on/off switch (10) to the off position marked with  “STOP”.
3.   The engine will now stop.

Running in the engine

1.   During the first 2–3 hours of work, run the engine at a moderate RPM.
2.   We advise you in any case not to maintain your engine at a high speed as 

the different components must settle with each other during the process 

of running in the engine.

3.   It is at the end of the running in period that the engine will reach its  

maximum power.

4.   After the first two hours of work, stop and make sure that all nuts and 

screws are securely fastened, and tighten them if necessary.

Maintenance & Cleaning

 

 WARNING.

 The engine of the petrol brushcutter / line trimmer must 

be at a complete stop during assembling, repair and cleaning  

operations that could be necessary.

General inspection

Regularly check that all the fixing screws are tight.  They may vibrate loose 

over time.  
Always check when first starting the motor for each use that the cutting 

head is not rotating under the power of the motor when the motor is at idle.
Do not perform any maintenance procedures with the motor in operation.  

Ensure the motor has stopped, and the on/ off switch is in the STOP position.  

The spark plug lead should be removed from the spark plug. 
Only use original Gardenline replacement parts when component parts 

require replacement.

Summary of Contents for 31CC 4 STROKE











































Reviews: