background image

 

 

 

 

 

 

 

 

 

 

 

  OVERVIEW

 

 

 

Change the remote control ID     

 

 

 

 

 

The remote control will be active only if the remote control ID matches with that specified on the

  

DVR. 
 
If multiple DVRs are installed on one place and you have just a single remote control, use the ID 
button to set the remote control ID. Only the ID-matching DVR can be controlled.

 

 

 

1.  From 

<SYSTEM> - <CONTROL DEVICE>

 under the System Setup menu, set the 

<REMOTE CONTROLLER ID>

 and press 

<Apply>.

 

Select between 00 and 99. For more details, refer to 

<SYSTEM SETUP> 

in  Operation 

manual. 
The remote control will be active only if the remote control ID matches with that of the 
DVR's system ID. 

2.  Press the 

[ID]

 button on the remote control. The default remote control ID is 00. 

3.  Use the number buttons to provide a two-digit ID. If you want to enter 01, for instance, 

enter the number 0 and 1 in sequence. 
Check if the remote control ID is set properly by manipulating the remote control. 

4.  To reset the ID to 00, press and hold the 

[ID]

 button. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for DR-16F44-AT



















Reviews: