Gamry Instruments IMX8 Operator'S Manual Download Page 12 | Manualshive

Page: 12 / 43

background image

Safety Considerations

12

Contact Gamry Instruments, Inc. if these measures do not solve the problem.

CE Compliance

The European Community has instituted standards limiting radio-frequency interference from electronic
devices and mandating several safety requirements. Gamry Instruments, Inc. has modified its instruments,
including the IMX8, to comply with these standards.

The relevant CE regulations include EN 61010.

RoHS Compliance

The IMX8 Multiplexer has been built using lead-free components and lead-free solder. It is in compliance with
the European RoHS initiative.

«
...
10
11
12
13
14
...
»

Summary of Contents for IMX8












































Reviews:

No comments

Related manuals for IMX8

Brand: Fluke Pages: 315

Brand: Vaisala Pages: 71

Brand: CABAC Pages: 13

Brand: Morris Pages: 13

Brand: Morris Pages: 9

Brand: Chauvin Arnoux Pages: 24

Brand: Chauvin Arnoux Pages: 84

Brand: Kusam-meco Pages: 19

Brand: Nexperia Pages: 32

Brand: Perel Pages: 20

Brand: Perel Pages: 36

Brand: Wavetek Pages: 20

Brand: Wavetek Pages: 22

Brand: Keysight Pages: 169

Retinomax K-plus 2

Brand: Nikon Pages: 69

Brand: Maxwell Digital Multimeters Pages: 27

Brand: YATO Pages: 36

Brand: Hameg Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands