manualshive.com logo in svg

Gambro AK 98, Operator'S Manual

The Gambro AK 98 Operator's Manual is available for free download from our website. This comprehensive manual provides essential instructions and guidance for operating the Gambro AK 98. Gain a deeper understanding of this product's features and functionality by accessing the manual at manualshive.com.

Share
Download
background image

HCEN12745 Revision 10.2016
Program version 2.xx

AK 98 Dialysis Machine - Attentions

B:85

510 Blood pump overloaded

510 Blood pump overloaded 

Check blood pump for obstruction. To continue
press Confirm. 

Appears:

When the blood pump is overloaded and can hardly run in
functional check.

Machine actions:

The blood pump stops.

Operator action:

1.

Check that the blood pump segment is correctly placed,
see Section 4.2.4

“Attach the arterial blood line”

on

page A:79 in Operators handbook.

2.

Press

Confirm

to continue.

If the attention appears again, contact an authorised
technician.

Mute time:

Permanent.

Summary of Contents for AK 98



































































































































































































































































































































































































Reviews:

No comments

Related manuals for AK 98

GE Druck DPI611 Quick Start Manuals preview
Druck DPI611
Brand: GE Pages: 14
GE Druck DPI 620 Safety And Quick Reference Manual preview
Druck DPI 620
Brand: GE Pages: 11
GE PACE5000 Calibration Manual preview
PACE5000
Brand: GE Pages: 20
GE Druck ADTS 2 Series Calibration Manual preview
Druck ADTS 2 Series
Brand: GE Pages: 18
AccuMed CMS-50D Manual preview
CMS-50D
Brand: AccuMed Pages: 14
TAS 3012 User Manual preview
3012
Brand: TAS Pages: 25
PANDROL CD100 User And Maintenance Manual preview
CD100
Brand: PANDROL Pages: 36
made for movement Xplore User Manual preview
Xplore
Brand: made for movement Pages: 51
Kamikaze KV 4 User Manual preview
KV 4
Brand: Kamikaze Pages: 112
KAM LED PAR 56 Product Manual preview
LED PAR 56
Brand: KAM Pages: 2
quadient IS-240 User Manual preview
IS-240
Brand: quadient Pages: 188
Radarsign TC-1000 Installation Manual preview
TC-1000
Brand: Radarsign Pages: 16
Össur QUICK-ALIGN Vari-Flex Instructions For Use Manual preview
QUICK-ALIGN Vari-Flex
Brand: Össur Pages: 36
Össur Patriot Collar Instructions For Use preview
Patriot Collar
Brand: Össur Pages: 2
Össur Unloader One Instructions For Use Manual preview
Unloader One
Brand: Össur Pages: 8
ProLights HZ900D User Manual preview
HZ900D
Brand: ProLights Pages: 28
Rainbow Colour Changers 8-Lite Plus Operator'S Manual preview
8-Lite Plus
Brand: Rainbow Colour Changers Pages: 22
Protech Machinery P200S Operator And Parts Manual preview
P200S
Brand: Protech Machinery Pages: 21

Brands by name

Popular brands

Load more brands