manualshive.com logo in svg

Gambro AK 98, Operator'S Manual

The Gambro AK 98 Operator's Manual is available for free download from our website. This comprehensive manual provides essential instructions and guidance for operating the Gambro AK 98. Gain a deeper understanding of this product's features and functionality by accessing the manual at manualshive.com.

Share
Download
background image

HCEN12745 Revision 10.2016
Program version 2.xx

AK 98 Dialysis Machine - Technical data and specifications

A:181

Contact time overnight
or when not in use
(recommended with
UFD)

If stored overnight a minimum of 3 hours dwell time is recommended.

Total time for
disinfection program

30 minutes (230 V and 115 V)

59 minutes (230 V) with UFD

65 minutes (115 V) with UFD

Time includes 10 min contact time

Concentration of
disinfectant

10 % available chlorine

Concentration in
machine

0.5 %; i.e. diluted 1 + 19 (1:20)

Volume

Approximate volume disinfectant used during disinfection program, 155
ml (with UFD approximately 163 ml)

Contact time between
treatments

10 minutes

Contact time

Maximum 20 min, not intended for overnight disinfection!

Total time for
disinfection program

29 minutes

50 minutes with UFD

Time includes 10 min contact time

Table 14-12. Hypochlorite Program (presettable)

14.1.11

Disinfection and cleaning - heat disinfection

Temperature:

93 °C (measured after heating rod)

≥80 °C (measured in the outlet before the heat exchanger)

NOTE!

The temperatures are verified at nominal values for the mains voltage and at 20 °C
ambient temperature.
Total time for disinfection programs is estimated and may vary.

One of four alternatives for heat disinfection can be selected. The second and third
alternatives are presettable for a combined heating program and the fourth is a
CLEANCART cartridge disinfection / heating program alternative.

The default settings are as follows:

Summary of Contents for AK 98



































































































































































































































































































































































































Reviews:

No comments

Related manuals for AK 98

Napoleon S1 Assembly Replacement Instructions preview
S1
Brand: Napoleon Pages: 2
Raytheon V800 Instruction Manual preview
V800
Brand: Raytheon Pages: 62
JBL Synthesis SDEC-3000 Calibration Manual preview
Synthesis SDEC-3000
Brand: JBL Pages: 24
Xilica Audio Design XP series User Manual preview
XP series
Brand: Xilica Audio Design Pages: 30
Laserworld EL-60 G Manual preview
EL-60 G
Brand: Laserworld Pages: 8
Laserworld EL 200 LED User Manual preview
EL 200 LED
Brand: Laserworld Pages: 6
LaserLiner ActivePen Manual preview
ActivePen
Brand: LaserLiner Pages: 56
LaserLiner AC-tiveMaster Operating Instructions Manual preview
AC-tiveMaster
Brand: LaserLiner Pages: 54
Vari Lite EVENTWASH VL800 User Manual preview
EVENTWASH VL800
Brand: Vari Lite Pages: 23
Vapotherm 2000i Operating Instructions Manual preview
2000i
Brand: Vapotherm Pages: 15
Xtool KC501 Manual preview
KC501
Brand: Xtool Pages: 8
Yamaha PLG150-AN Tutorial preview
PLG150-AN
Brand: Yamaha Pages: 5
Öhlins FCX 0301 Mounting Instructions preview
FCX 0301
Brand: Öhlins Pages: 8
?HC HC1200EB Quick Start Manual preview
HC1200EB
Brand: ?HC Pages: 2
Daekyung DTR-300N Operation Manual preview
DTR-300N
Brand: Daekyung Pages: 15
ABB PT004165 Operation Manual preview
PT004165
Brand: ABB Pages: 106
NSK Ti-Max NLX nano Operation Manual preview
Ti-Max NLX nano
Brand: NSK Pages: 38
Sensio Titan IP44 Installation Manual preview
Titan IP44
Brand: Sensio Pages: 3

Brands by name

Popular brands

Load more brands