Gallien-Krueger Fusion 550 Owner'S Manual Download Page 8

Fusion 550 Bass Amplifier

Horn Bi-Amp System

Horn Bi-Amp Mode:

    This mode requires a GK 

Horn  Bi-Amp  compatible  bass  cabinet.    Use  a 

properly  wired  four-conductor  Speakon  cable  to 

connect to your cabinet.  Set the switch on the back 

of your GK HBS compatible enclosure to Bi-Amp.  

In  this  mode,  the  cabinet’s  internal  crossover  is 

bypassed.    Use  the Woofer/Main  knob  to  control 

the output signal to the woofer, and the Horn knob 

to control the output signal to the horn. 

Note: 

The 50W horn amplifier has a fixed frequency 

output of 5kHz and up (high frequencies only).  It 

will not provide a usable signal to drive a separate 

speaker cabinet.

Full range Mode: 

   This mode is compatible 

with virtually any standard bass cabinet.  Use a 

two-conductor Speakon cable or a ¼” speaker 

cable to connect to your cabinet. If using a GK 

HBS compatible enclosure, set the switch on the 

back of the cabinet to Full range.  In this mode, 

the  cabinet’s  internal  passive  crossover  is  used  to 

split the signal between the woofer and horn.  Use 

the Woofer/Main knob on the front of the amplifier 

to control your output level.  The Horn knob is not 

used.  

Note: 

To avoid the risk of damage to the amplifier, 

do not use a four-conductor Speakon cable with non 

GK cabinets.  Instead use a two-conductor  Speakon 

or ¼” speaker cable.

CAUTION:    UNDER NO CIRCUMSTANCES 

SHOULD  THE  WOOFER/MAIN AMP AND 

THE 50 WATT HORN  AMP BE CONNECTED   

TOGETHER!!!

GK Speakon Cable Wire Configuration:

1+    Woofer Amp +

1-     Woofer Amp -

2+    Horn Amp +

2-     Horn Amp -

Horn Bi-Amp System (HBS):

Your amplifier incorporates GK’s unique HBS.  This feature is automatically engaged when you con-

nect to a GK HBS compatible enclosure, giving you independent control of the tweeter and woofer 

signals.  Now you can push the woofers to the max while the tweeter remains clean, crisp, and free of 

clipping distortion.  A smooth tight tone is easily dialed in by adjusting the Horn and Woofer Master 

controls on the amplifier’s front panel.

BI-AMP MODE

FULL RANGE MODE

Summary of Contents for Fusion 550













Reviews: