GALILEI LIBRA 70, Original Instructions Manual

Page: 46 / 52

k Cod. 80004180 – 04.04.2018
PARAMETERS TABLE
Attention
: the access to the programming menus and the modification of the parameters are
exclusively reserved to installation and maintenance personnel. A wrong or improper modification of the
parameters can lead to malfunctions and/or to a lack of performances.
Cabinet type: Libra R290
Controller: Dixell XR50CX
Defrost: Hot gas
Release Tabella: 80004180 – 04.04.2018
Programmation Table: 80004000
Parametertabelle
Cod. Type Parameter description u.o.m. Range Def.
SET - Set Point (valid only for stand-alone counters) °C LS÷US 3
Hy Pr1 Differential (Hystheresis) °C 0.1÷25.5 2
LS Pr2 Minimum Set Point °C -50÷Set -2
US Pr2 Maximum Set Point °C Set÷110 10
ot Pr1 Thermostat sensor calibration °C -12÷12 0.0
P2P Pr1 Evaporator sensor presence - n÷Y Y
oE Pr2 Evaporator sensor calibration °C -12÷12 0
P3P Pr2
Third sensor presence
- n÷Y N
o3 Pr2
Third sensor calibration
°C -12÷12 0
odS Pr2
Outputs delay at startup
min. 0÷255 2
AC Pr1
Min. time between Compressor Off and successive start
min. 0÷50 4
rtr Pr2
P1-P2 percentage for regulation (100=P1, 0=P2)
- 0÷100 80
CCt Pr2
Continuous cycle duration
H 0÷24 0
CCS Pr2
Set Point for continuous cycle
°C -55÷150 4
Con Pr2 Continuous ON time with faulty sensor min. 0÷255 10
CoF Pr2 Continuous OFF time with faulty sensor min. 0÷255 10
CF Pr2 Temperature measurement unit - °C÷°F °C
rES Pr1 Resolution (in=integer; de=decimal point) - In÷de De
Lod Pr2 Probe displayed - P1÷on on
dLy Pr2 Display temperature delay
Min. 0÷20 0
dtr Pr2 with Lod=dtr, percentage of visualization betw. temp. P1 and P2 - 1÷99 99
tdf Pr1 Defrost type (El=el.heater, in=hot gas) - El÷in in
dFP Pr2
Probe selection for defrost termination (nP,P1,P2,P3,P4)
- - P2
dte Pr1 Defrost termination temperature
°C -50÷50 7
idF Pr1
Interval between defrost cycles
h 1÷120 4
MdF Pr1
Maximum length of defrost min. 0÷255 30
dSd Pr2
Start defrost delay
min. 0÷99 0
dFd Pr2
Displaying mode during defrost (rt, it, Set, DEF)
- - SET
dAd Pr2
Max display delay after defrost
min. 0÷255 0
Fdt Pr2 Draining time min. 0÷120 5
dPo Pr2
First defrost after startup (n=after idF, y=immed.)
- n÷y Y
dAF Pr2 Defrost delay after fast freezing (0÷23h 50’) - - 0
ALC Pr2 Temperature alarm config. (rE=related to Set, Ab=absolute) - rE÷Ab rE
ALU Pr1 Maximun temperature alarm °C Set÷110 10
ALL Pr1 Minimum temperature alarm °C -50÷Set 5
AFH Pr2 Differential for temperature alarm recovery °C 0.1÷25.5 1
ALd Pr2 Temperature alarm delay min 0÷255 15
dAo Pr2 Delay of temperature alarm at startup h 0÷23h50’ 2