background image

4500MGB Quad Bay                                                                                         User Guide 

Page 9  /  Chapter 3 - System Set Up 

 

 

 

Only one interface 

can be used at any 

given time. 

 

 

Always connect the 

power adapter to 

your device before 

you plug it into the 

wall socket. 

 

 

Changing the RAID 

setup will require 

you to re-format the 

drives. Make sure 

you backup all data 

before doing so! 

 

 

Depending on the 

RAID mode, only a 

certain amount of 

drives can be used. 

RAID 

HDD 

BIG 

1-4 

FAST 

SAFE 

2 or 4 

SAFE II 

Chapter 3 - System Set Up 

Connection to your Computer 

A few precautions when using your external storage enclosure: 

  Check the cables for visible damage before turning it on 

  Do not expose the product to water or humid conditions 

  Do not cover the enclosure’s ventilation holes 

 

 

Hard Disk Mode 

When using your 4500MGB Quad Bay and more than one 

interface cable is connected, the USB connection has the 

priority. To use a different interface, make sure to disconnect 

any of the other cables first, before connecting the new one. 

 

When the device is turned on, the hard drives will keep 

spinning to provide immediate access to the data even when 

the Operating System goes into stand-by mode, so when not in 

use, we recommend always turning off the power. 

 

 

RAID Setup 

To change the RAID mode, remove the front panel to access 

the CONFIRM and MODE buttons. Keep in mind that when 

changing the RAID mode, the drives have to be re-formatted, 

so all data will be lost. 

 

1. Press and hold the CONFIRM button for 3 seconds until the 

three RAID mode LEDs blink two times. 

2. Press the MODE button to select the different RAID modes. 

It will cycle through BIG/FAST/SAFE/SAFE+FAST (SAFE II). 

3. Within 10 seconds after selecting the new mode, press the 

CONFIRM button to save the setting or otherwise it will 

revert back to the previous setup. 

Summary of Contents for 4500MGB Quad Bay























Reviews: