background image

12

Part / Material

Suggested Cleaning Procedure

Important Reminders

Pot Grid

Take pot grids off for cleaning.

Do not clean in a dishwasher.

(enamel on

Soak in sink. 

Soak burnt-in remainders in sink.

cast iron)

Clean with detergent  and brush.

Abrasive cleaners, used too vigorously or 
too often can eventually mar the enamel.

Burner Head Cover,

Remove coarse soiling with damp  

Do not clean in a dishwasher.

Burner Ring

cloth and detergent. 

Port openings must be kept free.

(brass)

Use brass polish to keep the 
original shiny surface. 

Burner Head 

Clean with detergent and brush.

Do not clean in a dishwasher.

(enamel on 

cast iron)

Electrode

Clean with brush, fine glass-paper

Soiled electrodes may cause malfunctions

or scouring pad.

when igniting or flame control disturbance.
Be careful when cleaning electrodes,
they are fragile, do not turn.

Caution: 

never switch on cooktop while 

cleaning electrodes.

Base

Cloth with detergent and hot water.

To prevent marring the polished stainless 

(stainless steel, 

Soak burnt-in remainders with a

steel trough, always polish in the direction

shot blasted, 

little detergent solution. 

of the polish lines.

brushed)

After cleaning, polish dry with a 

Light discolorations may form if the 

soft cloth to prevent water stains

natural oxidation is removed together 

forming on the surface. 

with the soiling. Put some commercially 

For heavy soiling, you can order 

available stainless steel polish on a cloth 

our stainless steel cleaner (Order 

and polish the whole cooktop after cleaning

No. 310631) from your Gaggenau 

to get an even stainless steel surface. 

dealer.

Never allow food stains or salt to remain 

Caution: 

no liquid should enter

on stainless steel for any length of time. 

the housing of the cooktop

Important: 

certain stainless steel cleaners 

through the burner base.

will scratch the surface. Chlorine or 
chlorine compounds in some cleaners are 
corrosive to stainless steel. Check 
ingredients on label.

Control knob

Wipe with a damp cloth.

Cloth should not be too wet, as moisture
could penetrate behind the control knob.

Summary of Contents for VG 411


























Reviews: