background image

9

Tools and accessories 

which are needed

Scope of delivery

Installation manual

Operating instructions

Installation accessories

Additional accessories

Installation accessories for Side-by-Side installation

For permanent connection of two appliances, 
e.g. a freezer next to a refrigerator.

Lateral additional heating

Necessary when the distance between two appliances 
is less than 160 mm.

Connecting element for furniture doors

For connecting two furniture doors (see explanation in 
Section “4. Preparing the furniture doors”). It can be 
used for standard height furniture doors without any 
preparation work.

Miscellaneous

Step ladder

Trolley, wheelbarrow or sack barrow

Hammer drill for drilling holes into the wall and floor

Various size drills for various materials

Wood plank, (min. 8 x 10 cm) as an alternative 
anti-tilt device. Length should correspond to the 
width of the installation niche.

Various size wood screws

Screw (M8, at least 80 mm long), nut

Thin (1.5 mm), material suitable for protecting the 
floor against damage (e.g. linoleum)

Suitable material for covering and protecting the 
cabinets (e.g. protective film)

Adhesive tape

Note:

Before using, check whether the removed adhesive 
tape leaves adhesive residue on the work surfaces! 
Otherwise do not use on high-quality work 
surfaces.

Tools

Rechargeable screwdriver

T20 Torx-bit magnetic 
holder

T20 Torx screwdriver

8 mm socket wrench

Various size drills

Fixed spanner SW 13 mm

Water pump pliers

Adjustable spanner

Knife with an adjustable 
blade

Metal tape measure, 
folding ruler

Angle of contact

60 cm and 120 cm spirit 
levels

Level, min. 120 cm long

Summary of Contents for RB 472


































Reviews: