background image

5

Installation Possibilities

Various installation possibilities are available.

These are only limited by the kitchen design and the 
finger protector function.

Stand alone appliance

Side-by-Side set up

* it is necessary to have a dividing wall!

If two appliances are set up next to each other, 
a sealing kit for Side-by-Side combination should be 
used in order to guarantee a stable connection.

For further information see section “Tools and 
Accessories which are needed”.

Stand alone appliance with dividing 
wall

When measuring the dividing wall for model 4, pay 
attention to the thickness of the furniture front to be 
mounted in order to avoid damage when opening 
doors at the same time.

If the distance between the appliances is less than 
160 mm, the auxiliary side heater must be used. 

For further information see section “Tools and 
Accessories which are needed”.

The minimum thickness of the dividing walls 
is 16 mm.

Stand alone appliance as an end 
section to a row of kitchen units

If a side of the appliance is visible, use a side covering.

The side covering must be connected firmly to the wall, 
the floor and the upper cupboards before the appliance 
is slid into the installation niche.

The dimensions of the side covering are governed by 
the opposing niche wall. During installation, make sure 
that the installation niche has right angles and has the 
exact size necessary for the appliance.

Summary of Contents for RB 472


































Reviews: