background image

3

9

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

I M P O R T A N T

  S A F E T Y

  I N S T R U C T I O N S READ

  AND

  SAVE

 TH

ESE

  I NSTRUC

TI O

NS

IMPORTANT: The appliance must be installed by a 
qualified installer. 

INSTALLER: please leave these instructions with this 
unit for the owner. Show the owner the location of the 
circuit breaker or fuse. Mark it for easy reference.

OWNER: Please retain these instructions for future 
reference.

WARNING

If the information in this manual is not followed exactly, 
fire or shock may result causing property damage or 
personal injury.

WARNING

Do not repair, replace or remove any part of the 
appliance unless specifically recommended in the 
manuals. Improper installation, service or maintenance 
can cause injury or property damage. Refer to this 
manual for guidance. All other servicing should be done 
by an authorized servicer.

Remove all tape and packaging before using the 
appliance. Destroy the packaging after unpacking the 
appliance. Never allow children to play with packaging 
material. 

Hidden surfaces may have sharp edges. Use caution 
when reaching behind or under appliance.

This appliance is intended for use up to a maximum 
height of 13,100 feet (4,000 meters) above sea level.

Improper installation is not covered by the warranty.

WARNING

Wearers of electronic implants

The appliance may contain permanent magnets which 
may affect electronic implants, e.g. heart pacemakers or 
insulin pumps. Therefore, during installation, wearers of 
electronic implants must maintain a minimum distance 
of 4 inch (10 cm) from the appliance. 

Safety Codes and Standards

This appliance complies with one or more of the 
following Standards:

UL 858, The Standard for the Safety of Household 
Electric Ranges

UL 507, The Standard for the Safety of Electric Fans

CAN/CSA-C22.2 No. 113-M1984 Fans and 
Ventilators

CAN/CSA-C22.2 No. 61-M89 Household Cooking 
Ranges

It is the responsibility of the owner and the installer to 
determine if additional requirements and/or standards 
apply to specific installations.

Electric Safety

WARNING

Before you plug in an electrical cord or turn on power 
supply, make sure all controls are in the OFF position.

If required by the National Electrical Code (or Canadian 
Electrical Code), this appliance must be installed on a 
separate branch circuit.

The circuit breaker should have a contact separation of 
at least 3 mm on all poles.

Be sure your appliance is properly installed and 
grounded by a qualified technician. Installation, 
electrical connections and grounding must comply with 
all applicable codes.

Before installing, turn power OFF at the service panel. 
Lock service panel to prevent power from being turned 
ON accidentally.

WARNING

IMPROPER GROUNDING CAN RESULT IN A RISK OF 
ELECTRIC SHOCK

Consult a qualified electrician if the grounding 
instructions are not completely understood, or if 
doubt exists as to whether the appliance is 
properly grounded. 

DO NOT USE AN EXTENSION 

CORD.

Summary of Contents for CI 292 610

































Reviews: