background image

WARRANTY

Seller  warrants  that  all goods covered by this catalog will conform to  

applicable  specifications  and  will  replace,  or  repair,  F.O.B.  our plant, any
goods  providing  defective  from  faulty workmanship, or material, for 90 days
from date  of shipment.

Said  warranty to remain in effect if and only if such goods are used in  

accordance  with  all  instructions  as  to  maintenance, operation, and use set
forth  in manuals and instruction sheets furnished by seller.

Sellers  obligation  under  this warranty shall be limited to the repair or  

rework of the goods supplied or replacement thereof, at Seller’s option, and in
no case is to exceed the invoice value of said goods. Under no circumstances
will  seller  be  liable  for  incidental or consequential damages or for damages
incurred  by  the  buyer  or subsequent  user in repairing or replacing defective
goods  or  if th e  goods covered by this warranty are reworked or subjected to
any type of additional   processing.

This warranty is void if  Seller is not notified in writing of any rejections

or defects within 90 days after the receipt of the material by the customer.

THIS   WARRANTY  IS  MADE  IN  LIEU  OF  ALL  OTHER  WARRANTIES,  
EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY.

GB902 Powerunit Kits

The GB902 Powerunit is available in various kits to suit your particular need.  The kits include

the GB902 Powerunit, hoses and hydraulic couplers. 

The GB902-12 Kit includes the GB902 Powerunit and a 12-foot Hose Kit, part number 902701

The GB902-26 Kit includes the GB902 Powerunit and a 26-foot Hose Kit, part number 902705

The GB902-38 Kit includes the GB902 Powerunit and a 38-foot Hose Kit, part number 902709

The GB902-52 Kit includes the GB902 Powerunit and a 52-foot Hose Kit, part number 902714

                                                                                                                                                                    

 

 

1/09

Summary of Contents for GB902










Reviews: