background image

9

 

REV. 3/21

 

 

 

GB714 INSTALLATION TOOL

.

S/N: 1001 AND ABOVE 

 

PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

 

Blind Fasteners

 

 

1.

 

Insert fastener.

 

 

 

 

 

 

 

 

 

 

 

 

2.

 

Insert fastener into nose assembly.

 

 

Note: Always hold tool so pulling head is perpendicular to surface of 

material in which fastener is being installed. Exert firm pressure 

against fastener during installation.

 

 

 

 

 

 

 

 

 

 

3.

 

Press actuator to start cycle. 

 

 

 

 

 

 

 

 

 

 

 

4.

 

Release actuator as soon as fastener breaks. 

 

 

5. 

 

Repeat steps 1

-

4.

 

 

Images may not reflect actual tool or fastener

 

HOW TO USE THE GB714

 

Lockbolts

 

 

#1. Insert fastener through the work piece.

 

 

 

 

 

 

#2. Slide collar over fastener.

 

 

Note: Always hold tool so pulling head is perpendicular to surface of 

material in which fastener is being installed. Exert firm pressure 

against fastener during installation.

 

 

 

 

 

 

 

 

#3.  Insert fastener into nose assembly. 

 

 
 
 
 
 

#4.  Press actuator to start cycle. 

 

 

#5.  Release actuator as soon as fastener breaks.

 

 

#6.  Repeat steps 1

-

5.

 

 

WARNING:  

Only qualified and trained operators should install, adjust or use the assembly power tool for non

-

threaded 

 

 

  mechanical fasteners. 

 

 

WARNING:  

Operator 

MUST 

read and understand all warnings and cautions.

 

 

WARNING:  

It is required that eye protection, hearing protection and safety boots be worn at all times while handling this 

equipment.

 

 

 

WARNING:  

The users or the user

s employer should assess specific risks that could be present  as a result after each use 

 

 

         

 

based on their application. 

 

 

 

 ●  

Be sure there is adequate clearance for tool and operator's hands before proceeding. Keep fingers clear of any 

 

     

 

 

moving parts. Keep fingers clear from fasteners and installed materials. Severe personal injury may result.

 

 

 

 

 ●  

Verify 

the air lines and/or hydraulic hoses are not a trip hazard.

 

 

 

 

 ●  

Ensure that there are no electrical cables, gas pipes, etc., which can cause a hazard if damaged by the tool

 

 

 

WARNING: 

 

Do not pull fastener in the air. Personal injury from fastener ejecting may occur.

 

 

WARNING: 

 

Air is exhausted from the bottom of the tool. Direct bottom of the tool (exhausted air) away from operator, other   

 

 

 

 

persons working in the vicinity, foreign matter and liquid.

 

 

WARNING: 

 

Do not carry from hoses or use as a hammer.

 

 

 

 

WARNING:  

Do not use in explosive atmosphere.

 

 

 

WARNING: 

 

Ensure air hose is securely connected to avoid possible hose whipping.

 

 

WARNING: 

 

Always disconnect air supply when tool is not in use to prevent accidental start

-

up.

 

 

WARNING: 

 

Be sure there is adequate clearance for tool and operator hands.

 

 

WARNING: 

 

Do not operate this tool without deflector, pintail catcher bag or pintail collection bottle in place.

 

 

CAUTION:  

 

Do not use beyond the design intent.

 

Summary of Contents for GB714





















Reviews: