manualshive.com logo in svg

Gage Bilt GB713SH, Installation Manual, Page: 2 / 14

Share
Download
Gage Bilt GB713SH Installation Manual Download Page 2

2 

REV. 11/14 

 

S/N: 1117 AND ABOVE  

PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. 

SPECIFICATIONS

 

 

 

 

 

Hand Held Weight 

-   2.50 lbs. (1.1 kg) 

 

 

 

 

Air pressure req'd 

-   90-100 p.s.i. (6.2-6.9 bar) 

 

 

 

 

Air consumption  

-   .29 SCF/cycle (8.21 L/cycle) 

 

 

 

 

Hydraulic oil 

 

-   Automatic Transmission Oil, 

 

 

 

 

 

 

    

    Dexron® III, or equivalent. 

 

 

 

 

 

 

 

 

Setting stroke   

-   .760" (19.3 mm) 

 

 

 

 

 

 

 

 

Noise level 

 

-   Less than 81.5 dB (A) 

 

 

 

 

Rated pull load   

-   4,500 lbs. (20 kN) 

 

 

                                  

 

Vibration 

 

-   Tested- No Hazards Found

 

 

TABLE OF CONTENTS

 

Description

                                                                                                                             

Page

 

 

Warnings ..................................................................................................................................................................................... 3 

Principle of Operation ................................................................................................................................................................ 4 

How to use the GB713SH .......................................................................................................................................................... 5 

Description, Maintenance, and Hydraulic Thread Preparation............................................................................................... 6 

Filling and Bleeding  .................................................................................................................................................................. 7 

Troubleshooting ......................................................................................................................................................................... 8 

Overhaul ...................................................................................................................................................................................... 9 

Disassembly and Parts Lists .............................................................................................................................................. 10-11 

DEXRON ® III Oil Safety Data .................................................................................................................................................. 12 

Nose Assembly Selection Chart ............................................................................................................................................. 13 

EU Conformity and Warranty .................................................................................................................................................. 14

 

Summary of Contents for GB713SH















Reviews:

No comments