background image

Rev 2/14 

 

S/N: 2094 AND ABOVE  

PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. 

 

Seller warrants that all goods covered by this catalog will conform 

to applicable specifications and will replace or repair, F.O.B. our plant, any 
goods providing defective from faulty workmanship, or material, for 6 
months from date of shipment

.  

 

Said warranty to remain in effect if, and only if, such goods are 

used in accordance with all instructions as to maintenance, operation and 
use, set forth in manuals and instruction sheets furnished by seller. 
 

Sellers obligation under this warranty shall be limited to the repair 

or rework of the goods supplied or replacement thereof, at Seller’s option, 
and in no case is to exceed the invoice value of said goods. Under no 
circumstances will the seller be liable for incidental or consequential 
damages or for damages incurred by the buyer or subsequent user in 
repairing or replacing defective goods or if the goods covered by this 
warranty are reworked or subjected to any type of additional processing. 
 

This warranty is void if Seller is not notified in writing of any 

rejections or defects within 6 months after the receipt of the material by the 
customer. 

THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES 
EXPRESSED OR IMPLIED, INCLUDING MERCHANTABILITY. 

 

WARRANTY 

 
 
 

DECLARATION OF CONFORMITY

 

 

WE DECLARE THAT THE EQUIPMENT SPECIFIED HEREIN 

CONFORMS TO THE FOLLOWING STANDARDS AND DIRECTIVES. 

 

EN12100-1 & EN12100-2 

EN13849 

EN792-1:2000+A1 

 

COUNCIL DIRECTIVE: MACHINE DIRECTIVE 2006/42/EC 

 

EQUIPMENT DESCRIPTION: 

GB51 FASTENER INSTALLATION TOOL 

 

MANUFACTURER: 

GAGE BILT Inc. 

 

    

SIGNATURE: 

 
 

NAME:  BRIAN LEIGH 

      

 

 

 

 

 

PRODUCT 

MANAGER 

      

 

 

 

 

 

CLINTON 

TWP., 

MI 

U.S.A. 

      

  

MAY 

2011 

      

  

(586) 

226-1500 

GAGE BILT 

DEXRON® IS A REGISTERED TRADEMARK OF GENERAL MOTORS CORPORATION.  TRUARC IS A REGISTERED TRADEMARK OF TRUARC COMPANY LLC. 

Summary of Contents for GB51









Reviews: