Gage Bilt GB2600 Original Instructions Manual Download Page 15

Page: 15 / 16

REV 1/20

GB2600 / GB2600A INTALLATION TOOL S/N: 1001 AND ABOVE

PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS

ACCESSORIES

GB2600 SELECTION CHART

(Sold Separately)

Riveter Kits Available

(Sold Separately)

Gage Bilt offers a wide selection of standard and custom kits

tailored to your needs.

FASTENER

DIA.

STRAIGHT NOSE ASSEMBLY

BOM12-2600-30

BOM12-2600-60

LGP14-2600-30

7/16"

LGP14-2600-30SC

LGP14-2600-65

NOTE: THE LAST 2 DIGITS OF THE NOSE ASSEMBLY REPRESENTS THE LENGTH THE

NOSE ASSEMBLY EXTENDS FROM THE TOOL. (I.e. -40 = 4.0 inches)

MAGNA-GRIP®

3/8"

MG12-2600-32

BOM ®, LGP® AND M AGNA-GRIP® ARE REGISTERED TRADEM ARKS OF ARCONIC INC.

GAGE BILT CERTIFIES THE GB2600 WILL INSTALL THE ABOVE FASTENERS

See gagebilt.com/nose_assemblies.php for nose assembly information (data sheets)

LGP®

BOM®

5/19

Summary of Contents for GB2600

















Search results

Summary of Contents for GB2600

Reviews:

Related manuals for GB2600

Brands by name

Popular brands

Gage Bilt GB2600, Original Instructions Manual

Search results

Summary of Contents for GB2600

Reviews:

Related manuals for GB2600

Brands by name

Popular brands