background image

10/13 

 

DESCRIPTION 
 

WARNING

THE BALANCE OF THIS TOOL IS DESIGNED FOR HORIZONTAL USE AND IS NOT SUITED FOR 

ANY OTHER APPLICATIONS.  GAGE BILT WILL BE PLEASED TO ADVISE FOR YOUR SPECIFIC 
APPLICATION. 

 

 

The  GB2581-750 is  a  hydraulic installation tool.  It weighs  6  lbs.  10 oz.  (3.0 kg).  It  has  a  .750" (19mm) rivet 
setting stroke and a rated pull load of 10,700 lbs (47.59kN)  @ 7,400 psi. (510.2 bar). 
 
Normal operating pressure is set at 7,400 psi. (510.2 bar) PULL pressure and 3,200 psi. (220.6 bar) RETURN 
pressure, enabling the tool to pull all the fasteners listed on the selection chart without adjusting pressures.  
Powerunit  may  be  set  to  the  pressures  only  needed  to  pull  your  specific  fastener  using  942280  pressure 
setting  gauge.  The  tool  comes  equipped  with  12’  hoses  and  electric  cord  kit  complete  with  quick 
disconnects. 

 

NOSE ASSEMBLIES ARE NOT FURNISHED WITH THE TOOL AND MUST BE ORDERED SEPARATELY.

 

 

 

MAINTENANCE 
 

WARNING

EXCESSIVE CONTACT WITH HYDRAULIC FLUID AND LUBRICANTS SHOULD BE AVOIDED. 

 

WARNING:

 

MAINTENANCE PERSONNEL 

MUST

 

READ AND UNDERSTAND ALL WARNINGS AND CAUTIONS. 

 

WARNING

DISCONNECT TOOL FROM ITS POWER SOURCE BEFORE PERFORMING MAINTENANCE. 

 

WARNING

BE SURE POWERUNIT IS DISCONNECTED BEFORE CLEANING OR WHEN REPLACING WORN 

 

OR DAMAGED COMPONENTS.  SEVERE PERSONAL INJURY MAY OCCUR IF POWER SOURCE 

 

IS NOT DISCONNECTED. 

 

 

The performance of any tool depends upon good maintenance practices. Following these minimal 
requirements for service and care will extend the life of your tool. 
 

*Only use a hydraulic power source equipped with relief valves and pressures set within                                                                     
 

specified limits. 

 

*Keep hydraulic system free of dirt. Avoid letting couplers contact a dirty floor. 

 

*Do not use as a hammer to force fasteners into holes or otherwise abuse tool. 

 

*Proper care by operators is necessary in maintaining full productivity and reducing downtime. 

 

*Check tool, all hoses and all couplings daily for damage or air/hydraulic leaks. Tighten or replace (if  

 

 

necessary).

 

 

IMPORTANT:

 

Be sure to use thread sealant on all hydraulic fittings, Loctite® 30534 or similar Teflon® infused pipe  

 

 

   dope is recommended. 

CAUTION:

 

Teflon tape is an excellent thread sealer. If it not properly applied,  

 

 

   however, pieces may enter the hydraulic system and cause malfunction and damage. Use 1 1/2 wraps  

 

 

   of tape on each thread. Cut off all loose tape ends. Tighten until fitting feels snug and then go 1/2 to a  

 

 

   full turn past  that point. 

CAUTION:

 Over tightening can easily distort the threads. 

Summary of Contents for GB2581-750










Reviews: