G+M Elektronik VA-FMC-512, Manual

Page: 7 / 9

gm-elektronik.swiss | adm@gm-elektronik.swiss
SETTINGS
UK
1
To leave the Settings mode and save the settings made, press the
ALERT
,
EVAC
and
RESET/ACK
keys again.
The RUN/SET key will start flashing again.
If you do NOT want to save the changes made, simply wait for the timeout (about 10 seconds), after which the
previous settings will be restored.
4.1 Address
Each station must have its own individual address. To set these addresses press the ALERT, EVAC and RESET/
ACK keys simultaneously, holding them down for more than 3 seconds.
Press the EVAC . key. The LEDs will show the current address setting ( factory default setting: 1 ).
To change an address, hold the EVAC key down, then press AUX (to increase the number) or P.T.T. (to decrease
it). The LEDs corresponding to the addresses are shown in the following table.
ADDRESS
1 2 3 4 5 6 7
LED
When the RUN/SET LED stops flashing and remains steady ON, release the keys.
There are 7 addresses at disposal, from 1 to 7 .
SETTINGS
UK
0
4.2 Priority
To set the priority of a station, it is necessary to press the keys ALERT, EVAC and RESET/ACK simultaneously
for more than 3 seconds . When the RUN/SET LED stops flashing and remains steady ON, release the keys. There
are seven priority levels at disposal (from 8 = lowest priority to 14 = highest priority) .
PRIORITY
8 9 10 11 12 13 14
LED
If you do NOT want to save the changes made, simply wait for the timeout (about 10 seconds), after which the
previous settings will be restored.
Note :
The priority level set determines the operational status both in emergencies and in broadcasting
conditions .
On pressing the ALERT key, the LEDs will indicate the current priority setting ( default factory setting: 8 ).
To change the priority, hold the ALERT key down and press AUX (to increase the number) or P.T.T. (to decrease it).
The LEDs corresponding to each priority level are shown in the following table.
To leave the settings mode and save the changes made, press the ALERT , EVAC and RESET/ACK keys again:
the RUN/SET LED will start flashing again.
Datasheet 1811.001
DIGITAL MICROPHONE CONSOLE VA-FMC-512
Page 7 | 9
3. Setting
3.1. Address
Each station must have its own individual address. To set
these addresses press the ALERT, EVAC and RESET / ACK
keys simultaneously, holding them down for more than 3 se-
conds.
When the RUN / SET LED stops flashing and remains stea-
dy ON, release the keys. There are 7 addresses at disposal,
from 1 to 7. Press the EVAC. key. The LED’s will show the
current address setting (factory default setting: 1). To change
an address, hold the EVAC key down, then press AUX (to in-
crease the number) or P.T.T. (to decrease it). The LED’s corre-
sponding to the addresses are shown in the following table.
ADDRESS
1 2 3 4 5 6 7
LED
„ FAULT „ FAULT „ FAULT „ FAULT „ FAULT „ FAULT „ FAULT
„ FAULT COM. „ FAULT COM. „ FAULT COM. „ FAULT COM. „ FAULT COM. „ FAULT COM. „ FAULT COM.
„ FAULT UNIT „ FAULT UNIT „ FAULT UNIT „ FAULT UNIT „ FAULT UNIT „ FAULT UNIT „ FAULT UNIT
„
DISABLE
„
DISABLE
„
DISABLE
„
DISABLE
„
DISABLE
„
DISABLE
„
DISABLE
„ BUSY „ BUSY „ BUSY „ BUSY „ BUSY „ BUSY „ BUSY
PRIORITY
8 9 10 11 12 13 14
LED
„ FAULT „ FAULT „ FAULT „ FAULT „ FAULT „ FAULT „ FAULT
„ FAULT COM. „ FAULT COM. „ FAULT COM. „ FAULT COM. „ FAULT COM. „ FAULT COM. „ FAULT COM.
„
FAULT UNIT
„
FAULT UNIT
„
FAULT UNIT
„
FAULT UNIT
„
FAULT UNIT
„
FAULT UNIT
„
FAULT UNIT
„ DISABLE „ DISABLE „ DISABLE „ DISABLE „ DISABLE „ DISABLE „ DISABLE
„ BUSY „ BUSY „ BUSY „ BUSY „ BUSY „ BUSY „ BUSY
To leave the Settings mode and save the settings made, press the ALERT, EVAC and RESE T / ACK keys again. The RUN / SET
key will start flashing again. If you do NOT want to save the changes made, simply wait for the timeout (about 10 seconds),
after which the previous settings will be restored.
3.2. Priority
To set the priority of a station, it is necessary to press the
keys ALERT, EVAC and RESET / ACK simultaneously for
more than 3 seconds. When the RUN / SET LED stops flas-
hing and remains steady ON, release the keys. There are
seven priority levels at disposal (from 8 = lowest priority to
14 = highest priority).
On pressing the ALERT key, the LEDs will indicate the cur-
rent priority setting (default factory setting: 8). To change the
priority, hold the ALERT key down and press AUX (to incre-
ase the number) or P.T.T. (to decrease it). The LEDs corres-
ponding to each priority level are shown in the following tab-
le. To leave the settings mode and save the changes made,
press the ALERT, EVAC and RESET / ACK keys again: the
RUN / SET LED will start flashing again.
If you do NOT want to save the changes made, simply wait for the timeout (about 10 seconds), after which the previous set-
tings will be restored. Note: The priority level set determines the operational status both in emergencies and in broadcasting
conditions.