USER CARD
TECHNICAL SURVEYS
1
SIGNATURE OF
PERSON
RESPONSIBLE
NUMBER OF DEVICE
USER NAME
CATALOGUE NO.
DATE OF MANUFACTURE
DATE OF INTRODUCTION INTO USE
DATE OF PURCHASE
2
3
4
5
DATE OF NEXT
SURVEY
SURVEY
DATE
REASONS FOR SURVEY
OR REPAIR
DAMAGES FOUND, REPAIRS
PERFORMED,OTHER NOTES
DEVICE NAME
MODEL
SAFETY HARNESS
Ref. AB 180 01
Size
M-XL
XXL
P-80
Serial number:
0000001
b
a
c
d
e
f
g
h
i
j
SIZES
Safety harness P-80/80E is made in two sizes:
- universal - M-XL
- extra extra large - XXL
Ref.: AB 180 01 - P-80
AB 180 02 - P-80E
READ THE INSTRUCTIONS
BEFORE USE
P-80/80E
EN 358:1999
EN 361:2002
EN 813:2008
EN 358:1999
EN 361:2002
EN 813:2008
max. load: 100 kg
The site where the equipment is used is responsible for completing the utilisation card.
The utilisation card should be filled in before the first release for use of the device.
All the information pertaining to the protective equipment (name, serial number, date of purchase and date of introduction into use, user name,
information about periodic surveys and repairs) should be included in the utilisation card of a device.
The card is filled in by the person in charge of protective equipment on site.
Pieces of personal protective equipment without a complete utilisation card must not be used.
!
overhauls, as well as withdrawals) must be placed in the utilisation card for a given device. The site where the equipment is used is responsible for completing the
utilisation card. The card is filled in by the person in charge of protective equipment on site. Pieces of personal protective equipment without a complete utilisation card
must not be used.
!
If the equipment is sold abroad, from the country of origin the equipment supplier should attach an operation and maintenance manual, as well as provide information about
periodic surveys and repairs in the language of the country where the equipment is to be used.
!
A piece of PPE should be immediately taken out of use if any doubts pertaining to its state or its normal operation occur. Putting it again into use is possible upon the
completion of a detailed survey carried out by the manufacturer of the equipment and their written approval for bringing it back to use.
!
An item of PPE should be taken out of use and withdrawn from use (destroyed) if it took part in the protection from fall incident.
!
The safety harness is the only acceptable device for keeping a body in an item of PPE for protection against falls from height.
!
A point (device) for the anchoring of a piece of equipment for protection against falls from height should have a stable design and location to limit the possibility of fall and to
minimise the length of free fall. The anchoring point should be located above its user's place of work. The shape and design of an anchoring point for a device should
guarantee a permanent fixation of equipment and cannot lead to accidental disconnection. Minimum static strength of the anchoring point for a piece of PPE equipment for
protection against falls from height is 15 kN. It is recommended to use certified and marked anchoring points of equipment complying with EN 795.
!
It is mandatory to check the free space under the work place where a piece of equipment for protection against falls from height is to be used to avoid the possibility of
hitting any objects or the surface underneath during possible fall. The amount of free space under a work place is to be checked in the operation manual for the PPE item to
be used.
!
During the use of equipment, pay special attention to any dangerous phenomena influencing the operation of the equipment and the safety of the user, especially:
- looping and sliding of ropes on sharp edges,
- pendulum falls,
- conducting electric current,
- any damage - cuts, wearing through and corrosion,
- influence of extreme temperatures,
- negative influence of climate,
- influence of chemicals,
!
An item of PPE should be transported in a packaging that protects it from damage or wetting, e.g. in bags made from impregnated fabric, steel or plastic cases or grates.
!
The PPE items must be cleaned in a way that prevents damaging the material (raw material) of the device. In the case of textile materials (tapes, ropes), use cleaning
agents for delicate fabrics. Can be washed by hand or in a washing machine. Rinse thoroughly. Plastic parts can be cleaned with water only. A PPE device that became wet
during cleaning or use should be cleaned thoroughly in natural conditions away from heat sources. Metal parts and mechanisms (springs, hinges, pawls etc.) may be
periodically lightly lubricated to improve their operation.
!
PPE devices should be stored in loose packaging in well-ventilated, dry rooms, protected against light, UV radiation, dust, sharp objects, extreme temperatures and caustic
substances.
All the information regarding the protective equipment (name, serial number, date of purchase and beginning of use, user name, and information regarding repairs and
Instructions for use
SAFETY
The safety harness is a basic item of PPE for protection against falls from a height that complies with EN 361 (safety harness), EN 358
(belts for work positioning and restraint) and EN 813 (sit harness).
Date of manufacture:
07.2008
a. Name/type of device.
b. Device model marking.
c. Catalogue number.
d. European standards.
e. Number of a notified body.
f. Month and year of manufacture.
g. Serial number of a device.
h. Size.
i. Note: read the instructions.
j. Manufacturer's or distributor's
marking.
k. Maximum load of sit harness.
DESCRIPTION OF MARKING
1. Shoulder belt.
2. Adjustment clamp of shoulder belt.
3. Front clamp for attachment of equipment for protection
against falls from a height.
4. Front attachment clamp for use only as sit harness
according to EN 813 (this clamp must not be used for
connecting equipment for protection against falls from a
height).
5. Side clamps of a sit harness. For use with ropes for work
positioning according to EN 358.
6. Sit harness for work positioning.
7. Side fixing and adjustment clamp of a sit harness.
8. Thigh belt.
9. Fixing and linking clamp of thigh belts.
10. Back clamp for attachment of equipment for protection
against falls from a height.
11. Crossing element.
12. Adjustment clamp of a back harness belt.
13. Pillow of a sit harness for work positioning.
14. Plastic clamps for attachment of tool bags.
15. Loops for attachment of tools.
16. Mark of harness.
1
2
3
4
5
6
7
8
9
10
11
12
16
15
14
13
HARNESS
k
SafetyLiftinGear.com
Unit R1D Rockingham Gate Poplar Way
West Cabot Park Bristol BS11 0YW
Tel: 0808 123 69 69 Fax: 0117 9381 602
Notified body, at which the European certification was
performed and which supervises
the production of the equipment:
APAVE SUDEUROPE SAS - BP 193 -
13322 MARSEILLE CEDEX 16 - FRANCE
