FXA FXAM1H-ZP5-250-1, Instruction Manual

Page: 9 / 100

9
It is also imperative to observe the accident
prevention regulations in force in your area. The same
applies for the general rules of occupational health
and safety.
Important! When using the equipment, a few safety
precautions must be observed to avoid injuries and
damage. Please read the complete operating
instructions and safety regulations with due care.
Keep this manual in a safe place, so that the
information is available at all times. If you give the
equipment to any other person, hand over these
operating instructions and safety regulations as well.
We cannot accept any liability for damage or
accidents which arise due to a failure to follow these
instructions and the safety instructions.
The manufacturer shall not be liable for any changes
made to the machine nor for any damage resulting
from such changes.
Even when the machine is used as prescribed it is still
impossible to eliminate certain residual risk factors.
The following hazards may arise in connection with
the machine’s construction and design:
Contact with the saw blade in the uncovered saw
zone.
Reaching into the running saw blade (cut injuries).
Kick-back of workpieces and parts of workpieces
Saw blade fracturing.
Catapulting of faulty carbide tips from the saw blade.
Damage to hearing if essential ear-muffs are not worn.
Harmful emissions of wood dust when the machine is
used in closed rooms.
Please note that our equipment has not been
designed for use in commercial, trade or industrial
applications.
Our warranty will be voided if the machine is used in
commercial, trade or industrial businesses or for
equivalent purposes.
SPECIFIC SAFETY INSTRUCTIONS
Do not use saw blades which are damaged or
deformed.
Replace the table insert/access plate if worn.
Use only blades as recommended in this manual,
which conform to EN 847-1. When changing a saw
blade ensure that the width of the groove (kerf) cut by
the blade is slightly greater than the thickness of the
riving knife. Also the thickness of the blade body must
not be greater than the thickness of the riving knife.
Take care that the selection of the saw blade is
suitable for the material to be cut.
Wear suitable personal protective equipment when
necessary. This could include:
Hearing protection to reduce the risk of induced
hearing loss.
Respiratory protection to reduce the risk of inhalation
of harmful dust.
Wearing gloves when handling saw blades or rough
material.
Saw blades should be carried in a holder whenever
practicable.
Never perform any operation freehand. This means
using only your hands to support or guide the
workpiece. Always use either the fence or mitre gauge
to position and guide the work.
WARNING! Freehand cutting is a major cause of
accidents.
Never attempt to free a stalled blade without first
turning the saw off. Turn the power off immediately to
prevent damage to the motor.
Provide adequate support for long or wide
workpieces.
Avoid awkward operations and hand positions where
a slip could cause your hand to move into the blade.
Do not operate the appliance with a damaged cord or
plug. If the supply cord is damaged, it must be
replaced by the manufacturer or its service agent or a
similarly qualified person in order to avoid a hazard.
ADDITIONAL SPECIFIC SAFETY RULES FOR
TABLE SAWS
WARNING! Before using your table saw it is important
that you read and understand these safety rules.
Failure to follow these rules could result in serious
injury to the operator or damage to the table saw.
Always use the blade guard. The blade guard must
always be used in every operation.
Hold the work firmly. Against the mitre gauge or rip
fence.
Always use a push stick. Especially when rip cutting
narrow stock.
Keep guards in place and in working order. Always
ensure that the riving knife is fitted and correctly
adjusted. Inspect the riving knife regularly and replace
it if it is worn. Use only a genuine FXA riving knife as
this is a dedicated component for this machine.
Remove adjusting keys and wrenches. Form the habit
of checking to see that keys and adjusting wrenches
are removed from the machine before turning it on.
Do not use in dangerous environment. Do not use
power tools in damp or wet locations, or expose them
to rain. Keep work area well lit. Keep the area well
ventilated.
Keep children away. All children and visitors should be
kept at a safe distance from the work area.