background image

GB

 INSTRUCTIONS BOOKLET

WARNINGS

A

  This instruction booklet must be kept together with the appliance for future 

reference. If the appliance is sold or consigned to other parties, check that 
the booklet is supplied with it, to ensure that the new user has the correct 
information on the operation of the range hood and is aware of the warnings. 
These warnings have been provided for the your safety and the safety of oth-
ers. As a result, please read them carefully before installing and operating the 
appliance. 

This appliance is not intended for use by young children or infirm persons un-
less they have been adequately supervised by a responsible person to ensure 
that they can use the appliance safely. Young children should be supervised 
to ensure they do not play with the appliance.
The appliance must be installed by qualified personnel, in accordance with 
the standards in force. If the supply cord is damaged, it must be re-placed 
by the manufacturer, its service agent or similarly qualified persons in order 
to avoid a hazard. Any modifications that may be required to the electrical 
system for the installation of the range hood must only be made by qualified 
electricians. 
It is dangerous to modify or attempt to modify the characteristics of this sys-
tem. In the event of malfunctions or if repairs are required to the appliance, 
do not attempt to solve the problems directly.
Repairs performed by unqualified persons may cause damage. For all repair 
and other work on the appliance, contact an authorised service/spare parts 
centre.
Always check that all the electrical parts (lights, exhaust device), are off when 
the appliance is not being used. Read the entire instruction booklet before 
performing any operations on the range hood.

The range hood must only be used for the exhaust of cooking fumes in home 
kitchens. The manufacturer disclaims all liability for any other use of the ap-
pliance. 
The maximum weight of any object placed above the hood, or hung to it (if 
possible) must not exceed 1,5 kilos. After installing the stainless steel hood, 
clean it in order to remove any residue of the protective glue, and stains of 
grease or oil. The manufacturer recommends its cleaning cloth available for 
purchase. The manufacturer accepts no liability in case of damage caused by 
the use of different detergent types.

TECHNICAL SPECIFICATIONS

B

The technical data pertaining to the electric appliance The technical specifica-
tions of the appliance are shown on the rating plates located inside the range 
hood.

Summary of Contents for Magnus Series











Reviews: