Link to the transmitter : FASST
1
Bring the transmitter and the receiver close to each
other, within 20 inches (half meter).
2
Turn on the transmitter and receiver.
3
Link operation is performed by the Link/Mode switch.
• When using TM-8 module, it's possible to set F/S position (only 3CH).
0 to 1 sec.
1 to 2 sec.
More than 2 sec.
0 sec.
1 sec.
2 sec.
Press and Hold time
No function
With
TM-8
(not included in this set)
To set the F/S
position(No re-link)
Re-link(ID set) and to
set the F/S position
No function
Besides
TM-8
Re-link(ID set)
*Refer to the instruction manual of the transmitter or module used
for a description of the linking operation, F/S position setting
methods and other details.
When using Multi prop (MPDX-1)
The
MPDX-1
can be used with
FASSTest
by merely
setting the corresponding transmitter. (Refer to the
instruction manual of the corresponding transmitter.)
When using the
MPDX-1
Multi Prop Decoder (sold
separately) with the
FASST
system, change the setting by
the following method.
Enable the
MPDX-1
at channels 11 and 12. (Initial value:
OFF)
Channels 11 and 12 cannot be used individually for
MPDX-1
output.
The
MPDX-1
extends 1 channel to 8 channels. However,
since the response speed becomes slower and there are
functional restrictions, use it at simple switch operation
and other applications that require numerous channels.
Multi prop mode Change method
1
. Switch the receiver to the FASST system (Normal or
High-speed).
2
. Turn on the receiver power. (Transmitter power off)
3
. Press the Link/Mode switch for at least 10 seconds.
4
. When the LED blinks red and changes to red/green
simultaneous rapid blinking, release the switch.
5
. The receiver enters the multi prop mode and the LED of
the current mode blinks. (Initial value: OFF)
6
. Each time the switch is pressed, the mode changes.
7
. When the receiver was switched to the desired mode,
press the Link/Mode switch for at least 2 seconds.
8
. When the LED switches to red/green simultaneous
rapid blinking, mode switching is complete. Release the
switch.
9
. When switching is complete, turn on the power. When
the power is turned on, the receiver switches to the new
mode.
FASST
When switched, the
R7018SB
can use the
FASST-Multi-ch
mode. When the
FASST
system is used, the telemetry and
Extra Voltage ports cannot be used. The
FASST
system has a Normal mode and a High-speed mode. However, in the
High-speed mode, analog servos cannot be used at CH1
〜
6.
Green LED blink
Mode
1 time
Multi prop mode OFF
2 time
Multi prop mode ON
FASST
est
FASST
When a telemetry adapter (TMA-1) is used
: FASSTest only
When using a
TMA-1
(sold separately), change the
settings by the following method.
The
TMA-1
is a device for viewing the telemetry data on
a smartphone or tablet.
R7018SB and TMA-1 linking method
1
. Switch the receiver to FASSTest system.
2
. Link the transmitter and receiver, and after confirming
operation, turn off the power.
3
. Turn on the receiver power. (Transmitter power off)
4
. Press the Link/Mode switch for at least 10 seconds.
5
. After the LED blinks red and changes to red/green
simultaneous rapid blinking, release the switch.
6
. The receiver enters the linked with TMA-1 mode, and
the LED begins red/green simultaneous rapid blinking.
7
. Press the TMA-1 link switch until the LED starts to blink
and wait for the TMA-1 to link.
8
. When TMA-1 linking is complete, the TMA-1 LED
changes from red to green for a moment.
9
. When linking is complete, turn on the receiver power
and check the operation of all the devices.
03';ق2SWLRQك
FUTABA CORPORATION
1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan
Phone: +81 475 32 6982, Facsimile: +81 475 32 6983
©FUTABA CORPORATION 2015, 4 (1)
R7018SB Specifications
FASSTest-2.4GHz
system(18CH/12CH mode)
FASST-2.4GHz
system
(Multi-ch mode)
S.BUS2
and
S.BUS
port and Linear 16 ch +Digital 2 ch for conventional
system receiver
• Dual antenna diversity
• Size: 2.15 x 1.59 x 0.64 in. (54.6x40.4x16.3mm)
• Weight: 1.48 oz. (42g)
• Power requirement: 6.0V to 7.4V(Voltage range: 4.8 to 8.4V)
• Battery F/S Voltage: It sets up with a transmitter (F/S can't be used in
case of FASST.)
• Extra Voltage port: 0
〜
70V DC
- 4 -
All product and company names mentioned
h e r e i n a r e t h e t r a d e m a r k s o r r e g i s t e r e d
trademarks of their respective owners.
本產品符合低功率電波輻射性電機管理辦法 第十二條、第十四條等條文規定
1. 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加
大功率或變更原設計之特性及功能。
2. 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，
並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率
射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
