Timer trigger mode
Defines the timer triggering mode:
[MAN]
=
Manual, through the
$
key.
[INI]
= Start up, when the controller is
powered up.
[TMP]
=Temperature, when the oven
working temperature is reached.
Note:
In modes
[INI]
and
[TMP]
the
$
key only cancels the timer.
[F12]
MAN TMP
-
MAN
Timer counting direction
Defines the direction the timer counts:
[DEC]
= time count down;
[CRE]
= time count up;
[F13]
DEC CRE
-
DEC
Timer time base
Defines the time base of the timer:
[MM:SS]
= minutes, maximum time
99:59 minutes;
[HH:MM]
= hours, maximum timer 99:59
hours.
[F14]
HH:MM
HH:MM
-
-
MM:SS
MM:SS
MM:SS
MM:SS
Timer reset mode
Defines the timer reset mode, essentially
wheter the audible alarm will be switched
off manually or by time:
[MAN]
=Manually through the
$
key;
[AUT]
=Automatically according to the
time defined in parameter F17;
Note:
The timer also resets when the door
of the oven is opened, independently of the
mode defined in this parameter.
[F15]
MAN AUT
-
MAN
Timer reset time base
Defines the time base when the timer is
reset:
[MM:SS]
= minutes, maximum time 99:59
minutes;
[HH:MM]
= hours, maximum time 99:59
hours.
[F16]
Time to reset the timer
(aut mode)
Defines the time to reset the timer if
automatic reset is selected in parameter
F15
[F17]
0:01 99:59 F16 0:05
MIN
MIN
MAX
MAX
UNIT
UNIT
DEFAU
DEFA
DESCRIPTION
DESCRIPTION
FUN
FUN
FUNCTION
FUNCTION
Steam working mode
Defines the steam operating mode for the
selected preset
[rCnF]
:
[OFF,]
Off: does not inject steam.
[MAN,]
M
anual:
injects steam when the
%
key is pressed.
[AUT,]
Automatic: automatically injects
steam after the timer is activated. The
steam is activated after the time set in F19
has elapsed.
[CYC,]
Cyclic: injects steam in cycles
using the times configured in
[UAon]
and
[Uaof]
.
Note:
When the preset mode is active, this
configuration is made in menu
[rUa,]
.
[F18]
OFF CYC
-
MAN
Delay to activate the
automatic steam
Defines the delay before injecting steam
into the oven after the timer is activated.
This parameter is valid when automatic
steam is adjusted in parameter F18.
[f19]
1
180
sec.
5
Time interval between
steam activations
Defines the minimum time interval between
steam activations, i.e. once the steam
output is activated, the controller will not
activate it again before the time adjusted in
this parameter has elapsed. To disable this
function, change the adjustment to the
minimum until
[no,]
is displayed.
Note:
This parameter is disregarded when
the type of steam selected is cyclic.
[f20]
no(0) 30
min. no(0)
Minimum temperature to
activate the steam
Defines the minimum temperature in the
oven to allow activating the steam output.
To disable this function, change the
adjustment to the minimum until
[no,]
is
displayed.
[f21]
no(-10)
no(14)
500
(932)
ºC
(ºF)
100
(212)
Economic mode - oven idle
time to switch of the light
Defines the time the oven has to be idle
before the controller enters in Economic
Mode (ECO). When the lightbulb output is
switched off. Press
to leave the ECO
dddd
mode.
[f22]
no(0) 60
min.
15
Fan output on time
Defines the time the fan will stay active in
each direction.
[f23]
60
600
sec. 180
Fan output off time
It must be adjusted with the time required
for the fan to stop, so that the rotation
reversion can be performed smoothly.
[f24]
5
30
sec.
15
SET
Maximum turbine off time
after deactivation
Automatic shutdown of the
turbine after completion of
the cooking time
Set the maximum time that the turbine
output will stay off after being manually
deactivated by the user or automatically
deactivated (case
F26
and
I09
are set to
YES
) after the time of the process timer has
elapsed.
Note:
The turbine can be switched off
manually or automatically only after the
process time has elapsed and the timer is
reset. If the timer is activated, the turbine
will be restarted.
Enables the option to automatically switch
off the turbine output after the timer
process time has elapsed (case
I09
is set
to
YES
).
Note:
The turbine will only be switched off
after resetting the timer and the output will
remain off for the time set in function F25 or
until the timer is activated.
[f25]
[f26]
1
NO
60
YES
MIN.
-
20
NO
Defines the functions lock mode:
[OFF,]
= functions lock disabled;
[LOC1]
= partial functions lock 1 -
p r e v e n t s a d v a n c e d c o n f i g u r a t i o n
parameters from being changed;
[LOC2]
= partial functions lock 2 -
prevents controller parameters from being
changed, only allowing changing presets;
[FULL]
= full functions lock, does not
allow any parameter adjustment.
Timer for function lock
Defines the time to lock / unlock the
functions. For more information, see item
7.4 - Functions Lock.
[f28]
1
30
sec.
10
Functions lock
[f27]
-
OFF FULL
-
LOC1
9. SIGNALING
Upon power up the controller indicates the operating mode of the oven.
9.1 Operating mode signaling
9.2 Programming signaling
Eletric Oven
Controller configured with the electric oven logic.
Gas-fired Oven
Controller configured with the gas-fired oven logic.
Wood-fired Oven
Controller configured with the wood-fired oven logic.
Controller configured with gas-fired oven logic with Default (standard) mode enabled,
without flame sensor monitoring. For more information, see item 7.5 Enable Default
(standard) operating mode.
Default Mode (standard)
Functions lock active
Does not allow adjusting the parameter
To deactive functions lock, see item 7.4 - Functions lock.
Parameter adjustment denied
Enter access code in parameter
[Cod]
to adjust the parameter value.
Receiving data via EasyProg* (programming key)
Updating the parameter table via EasyProg*.
*sold separately
9.3 Process signaling
If the controller detects an error that interferes in the operation of the system, the controller switches off the
outputs, switches on the audible alarm intermittently, and indicates the detected failure on the display. To leave
error mode, the controller must be switched off, the fault corrected, and the controller switched on again.
Note: In case the
I09 -Enable stand-by oven functionality
function has been set as
YES
, press the
>
key
during the error signaling to put the controller in stand-by and reboot it after the informed error is corrected.
Measure:
Contact Full Gauge Controls.
Measure:
Contact Full Gauge Controls.
Reason:
Temperature sensor disconnected or out of range.
Measure:
Check sensor connections and operation.
Reason:
Flame sensor shorted with the burner.
Measure:
Check wheter the flame sensor is making contact with the burner.
Delay of the temperature
control (GAS-FIRED OVEN)
When the controller tries to ignite the flame,
for example after the door is opened, the fan
is activated first and then the flame ignition
process commences after the time adjusted
in this parameter has elapsed.
Note:
This parameter is used when the type
of oven selected is GAS.
[F11]
no
(0)
30
sec.
5
