8. INSTALLATION
8.1 MOUNTING ON A DIN RAIL
8.2 BOLT FASTENING (OVER)
8.3 ELECTRICAL CONNECTIONS
Reinforcement bolts
(not included)
Wall
DIN rail
Instrument
1
2
DIN RAIL
WALL
Bolts
(not included)
70mm
Hole diameter
4mm
Merely illustrative images
WALL
HOLES
FOR FIXING
PUMP
N
115 Vac
230 Vac
or
F
C h e c k p o w e r s u p p l y
a c c o r d i n g t o p r o d u c t
model.
115 Vac
230 Vac
or
N
F
Check power supply
according to product
model
Charge
8.3.1 Differential Mode (Solar Heating)
8.3.2 Thermostat mode
PACKAGING:
Full Gauge products use packaging made from entirely recycled materials. Please dispose of it through specialized recyclers.
PRODUCTO:
The components used in Full Gauge controllers can be recycled and reused if they are dismantled by specialists.
DISPOSAL:
Do not burn or throw away controllers in the domestic waste, once they have reached the end of their working life. Observe the
existing legislation in your region regarding the disposal of electronic waste. If you have any questions, contact Full Gauge
Controls.
ENVIROMENTAL INFORMATION
WARRANTY - FULL GAUGE CONTROLS
Products manufactured by Full Gauge Controls, from May 2005, have a warranty period of 02 (two) years direct from the factory
and 01 (one) year from accredited retailers, starting from the consignment date on the sales invoice. After this year, the warranty
will continue to be honored for purchases from retailers if the device is sent directly to Full Gauge Controls. This period is valid in
Brazil. Other countries provide a guarantee for 2 years.The products are guaranteed in the event of a manufacturing fault that
makes them unsuitable or inappropriate for the uses to which they were intended. The warranty is limited to the maintenance of
devices manufactured by Full Gauge Controls, regardless of any other form of costs, such as any indemnity due to damage
caused to other equipment.
WARRANTY EXCEPTIONS
The Warranty does not cover transport and/or insurance costs for sending products believed to have defects or to have
malfunctioned to Technical Support. The following events are also not covered: natural wear of parts, external damage caused
by falls or improper packing of products.
LOSS OF WARRANTY
The product will automatically no longer be covered if:
- The instructions for use and assembly contained in the technical description and installation procedures listed in the
NBR5410 standard are not observed;
- It is subjected to conditions beyond the limits specified in its technical description;
- If it is breached or repaired by a person who is not part of Full Gauge Controls technical team;
- The damage which has taken place was the result of a fall, blow or impact, water damage, electrical surge or atmospheric
discharge.
USING THE WARRANTY
To take advantage of the warranty, the customer must sendo the product properly packed, together with the corresponding
purchase invoice, to Full Gauge Controls. The delivery cost for the product is borne by the client. You will also need to send as
much information as possible regarding the defect that has been detected, thus making it possible to streamline the analysis,
testing and servicing.
These processes and any eventual maintenance of the product will only be carried out by Full Gauge Controls Technical
Support, at the Company’s head office - Rua Júlio de Castilhos, 250 - Zip Code 92120-030 - Canoas - Rio Grande do Sul -
Brazil.
Rev. 03
Copyright 2020
All rights reserved
IMPORTANT
As instructed by standard NBR 5410:
1:
Install surge protectors on the power supply.
2:
Sensor and computer signal cables can be together, however not in the same cable chute of power
supply and load cables.
3:
Install transient suppressors (RC filter) in parallel to the loads, as a way to increase the working life
of the relays.
Wiring diagram for suppressors in the
contactors
Supressor
A1
A2
A1 and A2 are the contactor
coil terminals.
Wiring diagram for suppressors on direct loads
Load
Supressor
Take the maximum specified
current into account when using
direct activation
Power
supply
Power
supply
Sensor T1
white cable
Sensor T1
white cable
Sensor T2
black cable
Collectors
Thermostat
Pool / reservoir