Fukuda FRE-203XT User Manual Download

Page: 31 / 33

TROUBLE SHOOTING (CONTINUED)

Error

Cause & Solution

Laser Will Not

Self-Level

Outside Levelling Range Or Impact Damage

If the FRE-203XT is positioned outside of it’s self levelling range

of ±5 degrees the rotating laser prism will tilt over to one side (to

try and locate a level position) and then time-out.

Re-position the FRE-203XT so that is is within ±5 degrees of level

and try again.

If it’s within ±5 degrees of level and the prism remains tilted over

to one side, turn the laser OFF and On again and try again. If the

laser will still not self level, it may have received an impact which

has aﬀ ected the self levelling system.

Please contact the Service Department:

08000 869 769

who will

be able to how to send it for repair.

Laser Not Holding It’s

Charge

Battery Issue

Check the battery pack. The battery pack may require charging

or need to be replaced due to age and/or a high number of

charging cycles.

Check the battery compartment for signs of damage and ensure

that the compartment is clean and that the battery terminals are

not corroded.

Detector Not Detect-

ing The Laser Beam

Multiple Causes

Check the batteries in the detector. They may be low and need

replacing.

Check the FRE-203XT is spinning and producing a visible red

beam. You will be able to see the beam on your hands when

placed in front of the protective lighthouse.

Check the line of sight and ensure there is no obstructions.

Check that the laser level and detector are within the operat-

ing range. If you are too close to the laser it may not pickup the

beam. You need to be at least 3m away.

Check that the protective lighthouse glass is clean and free of

dust and dirt at all times.

Laser Will Not Power

Oﬀ

Poor Storage Conditions

If the FRE-203XT will not turn OFF, it is typically due to poor

storage (stored away wet, stored in a cold unheated building or

vehicle) etc. which has caused internal condensation to build up

and aﬀ ect the main circuit board.

Safely dry the Laser and accessories out thoroughly and try

again. If this does not resolve the issue, please contact the Ser-

vice Department:

08000 869 769

who will be able to advise how

to sending it for repair.

Summary of Contents for FRE-203XT


































Search results

Summary of Contents for FRE-203XT

Reviews:

Related manuals for FRE-203XT

Brands by name

Popular brands

Fukuda FRE-203XT, User Manual

Search results

Summary of Contents for FRE-203XT

Reviews:

Related manuals for FRE-203XT

Brands by name

Popular brands