Fujitsu XG0448 Hardware Manual Download Page 20

Page: 20 / 49

XG0448 Hardware Guide

Chapter 1 Getting Started

Items in the Package, Descriptions and Functions

LED Details

•

Ready LED

Indicates the operational state of the switch.

•

Error LED

Indicates a USB memory mount/access error occurred.

•

PSU LED

Indicates the switch power supply status.

•

Check LED

Lights orange when there is a problem. In such case, consult with the vendor's service
representative immediately.

•

Flash LED

Indicates the read/write status of the USB memory inserted into the switch.

Precautions

When the Flash LED is lit green, do NOT turn off power or reset the switch. The configuration being read or written may
be corrupted.

•

Ext.PSU LED

Indicates the status of the redundant power supply. Not supported.

•

Link/Act/Speed LED

Indicates the link status and communication speed/status of the RJ45 port.

•

Fdx LED

Indicates whether the RJ45 port is operating in half or full duplex mode.

•

SFP Link/Act LED

Indicates the link status and communication speed/status of the SFP module.

•

SFP LED

Indicates the link up/down status of the SFP module.

Check

Flash

Ext.PSU

Ready

Error

PSU

Link/Act/Speed

Fdx

SFP

Link/Act

SFP

Summary of Contents for XG0448


















































Search results

Summary of Contents for XG0448

Reviews:

Related manuals for XG0448

Brands by name

Popular brands

Fujitsu XG0448, Hardware Manual

Search results

Summary of Contents for XG0448

Reviews:

Related manuals for XG0448

Brands by name

Popular brands