Fujitsu PRIMERGY TX1330 M2 Operating Manual Download Page 65

Page: 65 / 86

TX1330 M2

Operating Manual

Starting up and operation

6.2.1.4

Indicators on the drives

Optical drive activity indicator

Lights up green when the storage medium is being accessed.

Hard disk drive indicators

Figure 9: Indicators on the 3.5 inch HDD modules

Figure 10: Indicators on the 2.5 inch HDD modules

1 LED

orange

HDD FAULT (orange)

(in conjunction with a RAID controller)

– Does not light: no HDD error
– Lights up: HDD Faulty or Rebuild Stopped (drive

defective/needs replacing, a rebuild process was stopped or
the HDD module is not correctly inserted)

– Slow flashing: HDD Rebuild (the data is being restored after

changing a drive)

– Fast flashing: HDD Identify

2 LED

green

HDD BUSY

– Lights up: HDD in active phase
– Does not light: HDD inactive (drive inactive)

햳

햲

햳

햲

Summary of Contents for PRIMERGY TX1330 M2























































































Search results

Summary of Contents for PRIMERGY TX1330 M2

Reviews:

Related manuals for PRIMERGY TX1330 M2

Brands by name

Popular brands

Fujitsu PRIMERGY TX1330 M2, Operating Manual

Search results

Summary of Contents for PRIMERGY TX1330 M2

Reviews:

Related manuals for PRIMERGY TX1330 M2

Brands by name

Popular brands